English
English
16
17
3 INSERTING BATTERIES (REMOTE CONTROL)
3A
Unscrew and
remove the
cover
3B
Insert 6 x 1.5 V AA batteries
and pay attention to the polarity,
as shown in the battery
compartment.
3C
Close the battery
cover and secure
with the screw.
1A
Counter-rotating
rotor blades
1B
Stabiliser
1C
Tail rotor
1D
LED lamps
1E
Charge socket
1F
ON/OFF switch
1 HELICOPTER
2A
ON/OFF switch
2B
Thrust controller
2C
Antenna
2D
Left/right trim
adjustment
2E
Controller for
forwards and
backwards flight
as well as rotation
2F
ON/OFF button
for LEDs
2 REMOTE CONTROL
4 CHARGING THE HELICOPTER
Attention:
The battery and motor must cool down for 10 to 15 minutes before
charging and after every flight. Otherwise they can be damaged. The charging process
must be constantly monitored. Always ensure that the charging process takes place on
a fireproof surface in a fire-resistant environment.
1. Switch off the helicopter and the remote control.
2. Plug the USB charger into a USB hub or a USB port on a computer
4A
.
If the charger is ready for operation, the LED on the top illuminates red.
3. Now insert the plug of the charger on the bottom side of the model
4B
.
The charging process begins automatically.
4. The Power LED on the charger goes out during the charging process and illuminates
red when the battery is full
4C
. After charging, disconnect the battery from the
charger and pull the charger plug out of the USB interface.
The helicopter can fly for approx. 6-8 minutes after a charge time of
approx. 40 minutes.
Warning notice:
The LiPo battery does not normally heat up while charging. If it
should become warm or even hot and/or changes to the surface begin to appear,
immediately discontinue the charging process!
You can also charge your helicopter with the remote control:
• Switch off the remote control and the helicopter.
• The plug for the charge cable is located on the back of the remote control
4D
. Remove
the cover and then carefully plug the cable into the charge socket of the helicopter
4E
.
The plug must be gently inserted into the charging socket – DO NOT USE FORCE. If the
plug is not correctly inserted into the charging socket, the helicopter may become
damaged and, under certain circumstances, become an injury risk. Switch on the
remote; the power LED blinks red. Slowly move the thrust controller to maximum and
then back to its starting position to activate the remote control
2B
; the power LED will
begin to blink quickly. This process lasts for approx. 3 seconds. Now the LED conti-
nuously illuminates green.
• The charging process is complete as soon as the LED is illuminated red.
• After the charging process, switch the power switch to „OFF“ and disconnect the
charge cable from the helicopter.
and neighbouring parts, as well as
physical injury!
• Never use a charger for NiCd/NiMH
batteries!
• Always ensure that the charging
process takes place on a fireproof
surface in a fire-resistant environment.
• Do not leave the battery unsupervised
during the charging process.
• Never disassemble or alter the battery
contacts. Do not damage or puncture
the battery cells. There is a risk of
explosion!
• The LiPo battery must be kept out of
reach of children.
• When disposing of batteries, they
must be discharged or their capacity
must be fully depleted. Cover exposed
terminals with adhesive tape in order
to prevent short-circuiting!
Maintenance and care:
• Please only use a clean, damp cloth
to wipe off the model.
• Protect the model and batteries from
direct sunlight and/or direct heat.
• Never allow the remote control and
charging unit to come into contact
with water, because the electronics
will be damaged as a result.
Technical changes and differences in
color reserved!
Required batteries for the
helicopter:
Rated output: DC 3.7 V / 0.67 Wh
Batteries: 1 x 3.7 V rechargeable
LiPo battery (integrated)
Capacity: 180 mAh
Charger:
Power supply: DC 5 V of
USB port of a PC or USB hub
Rated output: 4.2 V / up to 500 mA
Battery requirement for the remote
control:
Power supply:
DC 9 V
Batteries: 6 x 1.5 V “AA”
5 START PREPARATION
The thrust controller (the left controller on the remote control) must point down before
being switched on
5A.
Then set the remote control's ON/OFF switch to "ON"
5B
. The
power LED begins to blink.
Now set the helicopter's ON/OFF switch to the "ON"
5C
. Place the helicopter on the
ground so that the tail points toward you
5D
.
Activate the remote control by slowly moving the thrust controller to maximum and
then back to its starting position; the power LED will begin to blink quickly. This process
lasts for approx. 3 seconds. The helicopter is ready to start when the headlamp is
permanently illuminated red.
A A
A A
A A
A A
A A
A A
