A-2
rEm
star
p
lus
m s
ErIEs
u
sEr
m
anual
g
uIdanCE
and
m
anufaCturEr
’
s
d
EClaratIon
- E
lECtromagnEtIC
I
mmunIty
– This device is intended for use in the
electromagnetic environment specified below. The user of this device should make sure it is used in such an environment.
I
mmunIty
t
Est
IEC 60601 t
Est
l
EvEl
C
omplIanCE
l
EvEl
E
lECtromagnEtIC
E
nvIronmEnt
-g
uIdanCE
Conducted RF
IEC 61000-4-6
Radiated RF
IEC 61000-4-3
3 Vrms
150 kHz to 80 MHz
3 V/m
80 MHz to 2.5 GHz
3 Vrms
3 V/m
Portable and mobile RF communications equipment should be
used no closer to any part of the device, including cables, than the
recommended separation distance calculated from the equation
applicable to the frequency of the transmitter.
Recommended separation distance
d = 1.2 P
d = 1.2 P 80 MHz to 800 MHz
d = 2.3 P 800 MHz to 2.5 GHz
where P is the maximum output power rating of the transmitter in
watts (W) according to the transmitter manufacturer and d is the
recommended separation distance in meters (m).
Field strengths from fixed RF transmitters, as determined by an
electromagnetic site survey
a
, should be less than the compliance
level in each frequency range.
b
Interference may occur in the vicinity of equipment marked with
the following symbol:
NOTE 1 At 80 MHz and 800 MHz, the higher frequency range applies.
NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection from structures,
objects, and people.
a
Field strengths from fixed transmitters, such as base stations for radio (cellular/cordless) telephones and land mobile radios, amateur radio, AM
and FM radio broadcast and TV broadcast cannot be predicted theoretically with accuracy. To assess the electromagnetic environment due to
fixed RF transmitters, an electromagnetic site survey should be considered. If the measured field strength in the location in which the device is
used exceeds the applicable RF compliance level above, the device should be observed to verify normal operation. If abnormal performance
is observed, additional measures may be necessary, such as re-orienting or relocating the device.
b
Over the frequency range 150 kHz to 80 MHz, the field strengths should be less than 3 V/m.
r
ECommEndEd
s
EparatIon
d
IstanCEs
bEtWEEn
p
ortablE
and
m
obIlE
rf C
ommunICatIons
E
QuIpmEnt
and
t
hIs
d
EvICE
:
The device is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled. The customer or
the user of this device can help prevent electromagnetic interference by maintaining a minimum distance between portable and mo-
bile RF communications equipment (transmitters) and this device as recommended below, according to the maximum output power
of the communications equipment.
r
atEd
m
axImum
p
oWEr
o
utput
of
t
ransmIttEr
W
s
EparatIon
d
IstanCE
a
CCordIng
to
f
rEQuEnCy
of
t
ransmIttEr
m
150
K
h
z
to
80 mh
z
d = 1.2 p
80 mh
z
to
800 mh
z
d = 1.2 p
800 mh
z
to
2.5 gh
z
d = 2.3 p
0.01
0.12
0.12
0.23
0.1
0.38
0.38
0.73
1
1.2
1.2
2.3
10
3.8
3.8
7.3
100
12
12
23
For transmitters rated at a maximum output power not listed above, the recommended separation distance
d
in meters (m) can be estimated using
the equation applicable to the frequency of the transmitter, where P is the maximum output power rating of the transmitter in watts (W) according
to the transmitter manufacturer.
Note 1: At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies.
Note 2: These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection from structures,
objects, and people.
