RE926X_Flexible Bus WiFi Communicator
Page
1
of
8
10-Mar-15
24-hour Tech Support: (715)808-0164
www.ResolutionProducts.com
A/Rx
CLK
B/Tx
DATA
GND
+12V
Honeywell
Vista 20P or 15P
DATA OUT
7
DATA IN
6
AUX +
5
AUX -
4
Green
Y ellow
Red
Black
RE926X
WiFi
Module
RE926X Flexible Bus WiFi Communicator
Features
•
Connects panels to local WiFi Network
•
Compatible with:
o
Honeywell Vista® 15P and 20P
o
DSC PowerSeries®
o
Future: UTC NX, UTC Concord
•
Enables:
o
Alarm Reporting
o
Interactive Control Functions
o
Ethernet data reliability
o
Z-Wave Communicator included
Key Instructions
•
The same unit works for Vista & DSC PowerSeries
[Future: UTC NX, and UTC Concord].
•
Selectable switch determines panel compatibility.
•
DO NOT MOUNT INSIDE METAL CAN – there are radios on the boards that
need to be in free-air to communicate.
•
Communicator must be connected to a 12V nominal power supply with
battery backup, such as the control panel's aux power output.
•
RE926X communicates with the Vista 15P/20P via AUI device 2.
Enable AUI 2 in the Vista.
Wiring Instructions
NOTE:
Some programming must be done PRIOR to connection
Maximum cable lengths shown in the table below, this assumes the communicator is
the only device attached to the cable. If multiple devices share the same cable, the
maximum cable length must be derated accordingly.
Wire Size (AWG)
Maximum cable length to Control Panel
18
600
22
250
24
150
DSC
PowerSeries
Y EL
GRN
AUX - BLK
AUX + RED
Green
Y ellow
Red
Black
RE926X
WiFi
Module
A/Rx
CLK
B/Tx
DATA
GND
+12V
RE926X_Flexible Bus WiFi Communicator
Page
2
of
8
10-Mar-15
24-hour Tech Support: (715)808-0164
www.ResolutionProducts.com
Vista 20P and Vista 15P Programming:
Compatible Honeywell Panels:
Vista 20P
(version 3.0 or later) (controls partition 1 only)
Vista 15P
(version 3.0 or later)
1)
Refer to server setup instructions and set up the account on the Dealer
Portal.
2)
Be sure to add a contact that uses the system MASTER CODE to the account before
connecting the module. This will ensure the module can properly communicate
with and configure required system settings.
3)
Disarm the system (all partitions).
4)
The RE926X automatically communicates with the Vista using AUI device 2.
The panel is probably defaulted to this. If not, enable AUI 2 in the *189 field.
5)
Power down the Vista system.
6)
Set RE926X panel selector switch to Honeywell: DSC CDX HW UTC
7)
Connect the Vista and RE926X as shown in the Wiring Instructions above.
8)
Apply power to the Vista 15P/20P system.
The Vista control panel will begin automatic configuration.
Can move to Step 8 during this…
9)
WiFi Protected Setup connection to Router (see Operation – WiFi Protected
Setup connection to Router)
10)
The module will automatically connect itself to the server, and then enable
the following settings automatically:
IP/GSM device (*29)
Communicate to IP/GSM device first (*55)
Test Report off (*64)
Opening Report (*65)
Closing reports (*66)
Alarm cancel report (*68)
AC Power restoral report (*73)
Low Battery restoral report (*74)
Phone Monitor off (*92)
11)
Finally, the keypad(s) should display "DISARMED Ready to Arm".
12)
Installation is complete.
