Resol DeltaSol C/3 Mounting, Connection, Operation, Troubleshooting, Examples Download Page 18

D e lt a S o l

®

 

C/3

© RESOL 11150 deltasol_c/3.monen.ind

d

|

 

18

Stores cool down at night.

Does the collector 
circuit pump run in the 
night?

no

yes

Check controller.

At  night,  the  collector 
temperature  is  higher 
than  the  outdoor  tem-
perature.

no

yes

Check  the  non-return 
valve in flow and return 
pipe with regard to the 
functional efficiency.

Sufficient store insula-
tion?

yes

no

Increase insulation.

Insulation close enough 
to the store?

yes

no

Replace insulation or in-
crease it.

Are the store connec-
tions insulated?

yes

no

Insulate the connections.

Warm water flow up-
wards?

no

yes

Change connection and 
let the water flow side-
wards or through a siphon 
(bow  downwards);  less 
store losses now?

Does warm water circu-
lation run for a very long 
time?

no

yes

Use the circulation pump         
with timer and switch-off 
thermostat (energy effici-
ent circulation)

The solar circuit pump does not run although the collector 
is significantly warmer than the store.

Does the control LED 
flash?

yes

no

Does the pump start up 
in manual operation?

yes

No current; check fuses 
/ replace them and check 
power supply.

The adjusted temperature 
difference for starting the 
pump is to high; choose a 
value which makes more 
sense.

no

Is the pump current re-
leased by the controller?

yes

Is the pump stuck?

Turn the pump shaft using 
a screwdriver; now pas-
sable?

Pump is defective - re-
place it

Are the controller fuses 
o.k.?

Controller might be de- 
fective - replace it.

no

yes

no

no

yes

Replace the fuses.

Circulation  pump  and 
blocking valve should be 
switched-off for 1 night; 
less store losses?

yes

no

Check whether the pumps 
of the after-heating cir-
cuit runs at night, check 
non-return valve; problem 
solved?

no

no

yes

o.k.

Check  the  non-return 
valve in warm water cir-
culation- o.k.

yes

no

Further pumps which are 
connected  to  the  solar 
store must also be che- 
cked.

The gravity circu lation in 
the circulation line is too 
strong; insert a stronger 
valve in non-return valve 
or an electric 2-port val-
ve behind the circulation 
pump; in pump operation, 
the 2-port valve is open, 
other wise it is closed, co-
nect  pump  and  2-port 
valve in parallel; activate 
circulation again!

Clean or replace

a

a

b

b

Summary of Contents for DeltaSol C/3





















Reviews: