Reshable MR11L0224 User Manual Download Page 10

   

 

 

   

 

 

 

 

 

   

 

 

   

   

 

 

 

 

   

 

 

 

 

 

   

 

 

 

 

 

 

 

   

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Q:How to maintain the backrest or seat

 

daily?

Q: How to maintain the hydraulic pump?

A: The PVC leather should be cleaned

 

regularly. Spray a little of the leather care

 

solution onto a sponge and then use the

 

sponge to wipe the leather surfaces

 

gently.

A: Keep the surfaces of the hydraulic

 

pump (including the centre shaft) clean.

Sit on and raise/lower the chair

 

periodically to expel the air inside.

Regularly wipe the hydraulic pump with

 

anti-rust oil.

Daily Maintenance

1

8

1

7

OPERATE THE CHAIR

OPERATE THE CHAIR

Dear Customer, if you have any advice or questions on the installation 

or product after receiving, please give us feedback as soon as possible. 

We will provide you with professional guidance. Please feel free to use 

it.

A: Please check whether the foot lever is 

stepped to the lowest. If it's the lowest but 

still has the problem, there could be 

something wrong with the pump. You need 

to replace it.

Q: What if the chair is difficult to rotate?

Q: How to prevent the chair from leaning 

forward?

A: In this case, there may be something 

wrong with the installation. Please check 

whether the mounting direction of the seat 

chassis connector is wrong. The direction 

of the slot in the seat chassis connector 

should be opposite to that of the footrest 

(refer to the detail drawing in STEP6). 

When it is confirmed, please make sure 

whether the hydraulic pump is properly 

inserted into the pump pin.

Q: If the chair keeps tilting and cannot be 

righted, what should I do?

A: In this case, there may be air in the 

pump. Please sit on the chair and raise it to 

the highest, then lower it. Repeat the 

above action until it can be used normally. 

Q: What should I do when the seat cannot 

be lifted or lowered normally?

A: When you sit on the chair and lean all 

your weight forward deliberately, the chair 

will indeed tilt. So please notice this point: 

if both your feet are on the footrest, please 

sit back as far as you can; meanwhile, 

please ask the barber or someone else to 

step the foot lever and set the chair to the 

lowest when the guest sitting on the chair 

is ready to stand up. (Note: please remind 

guests not to stand on the footrest with 

both feet, please put one foot on the 

ground first.)

Frequently Asked Questions

Summary of Contents for MR11L0224











Reviews: