manualshive.com logo in svg

Republic Manufacturing RB1200HC, Maintenance Schedule, Page: 5 / 25

Share
Download
Republic Manufacturing RB1200HC Maintenance Schedule Download Page 5

5

DRIVE BELT INFORMATION

Republic utilizes a 16-groove belt on all its centrifugal blowers and has the part number stamped on the flat 

side of the belt. Republic recommends that you keep spare belts in stock. It is also recommended that replace-

ment belts be purchased from a Republic distributor, to ensure that belt quality and blower performance are maintained.

Belts do vary from manufacturer to manufacturer, and all Republic belts are inspected for belt thickness and 

imperfections prior to shipment.

BELT SIZING INFORMATION

Please find the part number stamped on the face of the small stainless steel blower pulley, and then refer to the 

following chart for the correct belt size.

RB800/ RB1200HC REPLACEMENT PARTS REFERENCE

Blower Pulley Part No.

Belt Part No.

Tension Pulley Part No.

RB800

RB1200HC

RB800

RB800-STB

RB1200HC

RB800

RB1200HC

230-0145

N/A

230-3800K

230-5925

N/A

200-0214

N/A

230-0155

231-0155

230-3800K

230-5925

230-4600K

200-0214

200-0206

230-0165

231-0165

230-3800K

230-5925

230-4600K

200-0214

200-0206

230-0175

231-0175

230-3800K

230-5925

230-4700K

200-0214

200-0206

230-0185

231-0185

230-3800K

230-5925

230-4700K

200-0214

200-0206

230-0195

231-0195

230-3800K

230-5925

230-4700K

200-0214

200-0206

230-0205

231-0205

230-3800K

230-5925

230-4700K

200-0214

200-0206

230-0215

231-0215

230-3900K

230-5925

230-4700K

200-0214

200-0206

230-0225

231-0225

230-3900K

230-5925

230-4700K

200-0214

200-0206

230-0235

231-0235

230-3900K

N/A

230-4700K

200-0214

200-0206

230-0245

231-0245

230-3900K

N/A

230-4700K

200-0214

200-0206

230-0255

231-0255

230-3900K

N/A

230-4800K

200-0214

200-0206

230-0265

231-0265

230-3900K

N/A

230-4800K

200-0214

200-0206

230-0275

231-0275

230-3950K

N/A

230-4800K

200-0214

200-0206

230-0285

231-0285

230-3950K

N/A

230-4900K

200-0214

200-0206

230-0295

231-0295

230-3950K

N/A

230-4900K

200-0214

200-0206

Important: Replace spring with every belt replacement to ensure proper tension on your new belt. The follow-

ing pages should show the proper procedures for belt installation and removal and for spring replacement.

REPUBLIC CENTRIFUGAL BLOWER MAINTENANCE SCHEDULE

RB800, RB1200HC, RB2400

COMBINED FLUID PRODUCTS COMPANY 

www.cfpco.com  

●

  [email protected]  

●

  +1 (847) 540-0054

Summary of Contents for RB1200HC


























Reviews:

No comments