Republic Manufacturing RB1200HC Maintenance Schedule Download Page 25

25

25

WARRANTY TERMS AND CONDITIONS

Republic Manufacturing® Company warrants all finished Republic Blower Systems® products to be free 

from functional defects in material and workmanship for a period of twelve (12) months from the date of 

installation, or no longer than eighteen (18) months from shipment.

Wear parts such as drive belts, filter elements, hoses and pulleys are not covered by the 12 to 18 month 

warranty.

DISASSEMBLY OF BLOWER MAY VOID WARRANTY.

To obtain service within the warranty period, first contact your authorized Republic Sales & Manufactur-

ing® dealer or Republic Sales & Manufacturing® Service Department. Republic’s responsibility under this 

warranty shall be to provide an analysis of the blower, which will determine course of action. Any product 

found to be defective within the warranty period will merit either:

a. A no charge repair of existing blower. Any freight charges will be the purchaser’s responsibility.

b. A replacement blower*. Any freight charges will be the purchaser’s responsibility.

*This option would be chargeable replacement until the original blower is received by Republic Manufac-

turing, and warranty is approved.

Republic Manufacturing® shall not be liable for incidental nor consequential damages resulting from the 

use of this product. There are no expressed nor implied warranties, which extend beyond the warranty of 

merchantability or fitness for a particular purpose to the equipment and/or its parts and components.

REPUBLIC CENTRIFUGAL BLOWER MAINTENANCE SCHEDULE

RB800, RB1200HC, RB2400

COMBINED FLUID PRODUCTS COMPANY 

www.cfpco.com  

  [email protected]  

  +1 (847) 540-0054

Summary of Contents for RB1200HC


























Reviews: