Rentech Jaguar 1.2K User Manual Download Page 12

10 

 

6. Trouble Shooting 

Use the table below to solve minor problems. 

Problem 

LCD/LED/Buzzer 

Explanation / Possible cause 

What to do 

When power fails, 
the backup time is 
shorten. 

Battery low alarm 
issue quickly. 

Battery voltage is too low. 

Charge  the  unit  at  least  8 
hours. 

Battery  capacity  is  not  full  even 
after charge the unit for at least 8 
hours. 

Check  the  date  code  of  the 
battery.  If  the  batteries  are 
too old, replace the batteries. 

Mains exist but the 
unit works in 
battery mode. 

Input voltage is 
displayed as 0 on the 
LCD and green LED is 
flashing. 

Input protector is tripped 

Check if AC breaker is tripped 
and  AC  wiring  is  connected 
well. 

Green LED is flashing. 

Insufficient quality of AC power. 
(Shore or Generator) 

1. Check if AC wires are too 
thin and/or too long. 
2. Check if generator (if 
applied) is working well or if 
input voltage range setting is 
correct. (Narrow

Æ

Wide) 

No LED display on 
the front panel 
when the utility 
power is normal. 

No LED display. 

Battery is not connected well. 

Check the external battery 
cable and terminal. Make sure 
all the battery connections to 
the unit are all correct. 

Battery defect.   

Replace the batteries. 

Buzzer beeps 
continuously and 
red LED is on. 

Fault code 00 

Output short circuited.   

Check if wiring is connected 
well and remove abnormal 
load.   

Fault code 01 

Overload error. The inverter is 
overload 110% and time is up. 

Reduce the connected load by 
switching off some 
equipment. 

Fault code 03 

Output voltage too high 

Return to repair center. 

Fault code 05 

Fan fault 

Replace the fan. 

Fault code 06 

Internal temperature of inverter 
component is over 100°C. 

Check whether the air flow of 
the unit is blocked or whether 
the ambient temperature is 
too high. 

Fault code 08 

Battery is over-charged.   

Return to repair center. 

The battery voltage is too high. 

Check if spec and quantity of 
batteries are meet 
requirements. 

If there is any abnormal situations occur, which doesn't list above, please call the service people immediately 
for professional examine. 

 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for Jaguar 1.2K















Reviews: