c)
Persons and product
•
Never pour liquids over electrical devices or place objects filled with liquid next
to the device. If liquid or a foreign object enters the interior of the device never
-
theless, first power down the respective power supply (e.g. switch off the circuit
breaker) and then pull the mains plug from the mains socket. Discontinue use and
take the product to a specialist repair centre.
• Never use the product immediately after it has been brought from a cold room into
a warm one. This may cause condensation to form, which can destroy the product.
Allow the product to reach room temperature before connecting it and putting it
into use. This may take several hours.
• Do not block any ventilation openings in the housing during operation.
Operation
•
Remove the housing cover. Unscrew the fixing screw with a suitable screwdriver.
• Remove the housing cover.
• You can now install a circuit board. Screw the Raspberry Pi
®
circuit board in the housing
using the four screws supplied.
• The fan requires two screws for mounting in the housing.
• Connect the connector plug of the fan to the power supply provided on the circuit board.
• Close the housing cover again and tighten the housing screw.
Care and cleaning
• This product does not require maintenance.
• Disconnect the product from the power supply before cleaning.
• Never use aggressive detergents, rubbing alcohol or other chemical solutions, as these
may damage the housing or stop the product from functioning properly.
• Use a dry, lint-free cloth to clean the product. Dust can be removed from the ventilation
openings easily using a clean, soft brush and a vacuum cleaner.
Disposal
Electronic devices are recyclable waste and must not be placed in household waste.
At the end of its service life, dispose of the product in accordance with applicable
regulatory guidelines.
You thus fulfil your statutory obligations and contribute to environmental protection.
Technical data
Input voltage
................................. 5 V/DC, 0.2 A
Suitable for ................................... Raspberry Pi
®
2B - 4B
Connector .....................................
Dupont connection for GPIO pin
Cable length ................................. 8 cm
Housing material ........................... Aluminium
Fan speed ..................................... 8000 rpm
Air flow rate
................................... 3.09 CFM
Operating conditions
..................... -20 to +60 °C, 10 - 80 %
relative humidity (non-condensing)
Storage conditions ........................ -20 to +60 °C, 10 - 80 %
relative humidity (non-condensing)
Fan dimensions ............................ 30 x 30 x 7 mm
Dimensions (L x W x H) ................ 95 x 85 x 35 mm
Weight .......................................... 50 g
Operating instructions
Raspberry Pi
®
aluminium housing with fan
Item no. 2253747
Intended use
The product is designed to be installed and attached to a suitable Raspberry Pi
®
circuit board
(see ‘Technical data’). A supplied fan is used to cool the integrated circuit board during ope-
ration. The fan is supplied with power via the corresponding connection on the circuit board.
This product is intended for indoor use only. Do not use it outdoors. Contact with moisture (e.g.
in a bathroom) must be avoided under all circumstances.
For safety and approval purposes, do not rebuild and/or modify this product. Using the product
for purposes other than those described above may damage the product. In addition, improper
use can cause hazards such as a short circuit or fire. Read the operating instructions carefully
and store them in a safe place. Only make this product available to third parties together with
its operating instructions.
This product complies with statutory, national and European regulations. All company and pro-
duct names contained herein are trademarks of their respective owners. All rights reserved.
Delivery content
• Aluminium housing
• 30 mm fan
• 7x screws
•
Operating instructions
Up-to-date operating instructions
Download the latest operating instructions at www.conrad.com/downloads or
scan the QR code shown. Follow the instructions on the website.
Explanation of symbols
The symbol with an exclamation mark in a triangle is used to highlight important
information in these operating instructions. Always read this information carefully.
The arrow symbol indicates special information and tips on how to use the product.
This product has been CE tested and therefore complies with the necessary national
and European regulations.
Safety information
Read the operating instructions and safety information carefully. If you do not
follow the safety information and information on proper handling in these ope
-
rating instructions, we will assume no liability for any resulting personal inju
-
ry or damage to property. Such cases will invalidate the warranty/guarantee.
a) General information
• The device is not a toy. Keep it out of the reach of children and pets.
•
Do not leave packaging material lying around carelessly. It may become a dange
-
rous plaything for children.
• Protect the product from extreme temperatures, direct sunlight, strong jolts, high
humidity, moisture, flammable gases, vapours and solvents.
• Never expose the product to mechanical stress.
•
If it is no longer possible to operate the product safely, stop using it and prevent
unauthorised use. Safe operation can no longer be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Handle the product carefully. Jolts, impacts or a fall even from a low height may
damage the product.
• Consult a technician if you are not sure how to use or connect the product, or if
you have concerns about safety.
•
Maintenance, modifications and repairs must be carried out by a technician or a
specialist repair centre.
•
If you have questions which remain unanswered by these operating instructions,
contact our technical support service or other technical personnel.
b) Connected devices
• Always observe the safety information and operating instructions of any other de-
vices which are connected to the product.
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or capture in electronic
data processing systems, requires the prior written approval of the publisher. Reprinting, also in part, is prohibited. This
publication reflects the technical status at the time of printing.
Copyright 2020 by Conrad Electronic SE.
*2253747_1_0620_02_DS_m_2L_(1)