• The product is not a toy. Keep out of the reach of children and pets.
• Do not carelessly leave the packaging material lying around, since it could be-
come a dangerous plaything for children.
• Handle the product with care; it can be damaged by impacts, blows or falls even
from a low height.
• If you have any questions that are not answered in this manual, please contact our
technical service or another specialist.
Product overview
1
Recessed “Reset“ button
2 “WPS“
button
3
On/Off slider switch
4 LAN
port
5 WAN/LAN
port
6
Slider to select the mode
7 Status
LEDs
Power
(lit, as soon as the device is turned on)
LAN
OLWZKHQFRQQHFWHGÀDVKLQJZKHQGDWDLVWUDQVPLWWHG
WAN/LAN
OLWZKHQFRQQHFWHGÀDVKLQJZKHQGDWDLVWUDQVPLWWHG
WPS
ÀDVKHVIDVWZKHQWKHFRQQHFWLRQWR\RXUURXWHULVHVWDEOLVKHGÀDVKHVVORZO\
when attempting to establish a connection to your device)
WiFi LEDs (indicate the signal strength; 3 LEDs 100%; 2 LEDs 50% – 75%; 1 LED below
QRFRQQHFWLRQLIWKH¿UVW/('LVÀDVKLQJLQ5HSHDWHUPRGH
Standard settings:
&RQ¿JXUDWLRQDGGUHVV
http://ap.setup
6WDQGDUG,3DGGUHVV
192.168.10.1
3DVVZRUG
admin
Connection and start-up
• Plug the device into a mains socket.
• Depending on the application, align the antennas as shown in the two pictures.
• Use the mode selection slider (6) to select the desired mode. You can choose between the
modes “Repeater”, “Access Point” (AP) and “Router”.
• If you have selected the “Access Point” mode, connect the WAN/LAN port to a network port
on your router over an Ethernet cable.
• If you have selected the “Router” mode, connect the WAN/LAN port to the appropriate port
on your modem over an Ethernet cable. Turn on your modem.
• Turn the product on by means of the slider switch (3) (position “ON“) and wait until the start-
XSSURFHGXUH¿QLVKHV7KLVPD\WDNHDSSUR[PLQXWHV
Operating instructions
WLAN Repeater AC1200
Item no. 1902086
Intended use
The product features 3 operating modes “Repeater”, “Access Point” (AP) and “Router”.
“Repeater” mode is used to amplify your existing WLAN network and extend the coverage area.
“Access Point” (AP) mode provides a separate WLAN network.
“Router” mode is used to connect the devices that are connected to the product to the Internet
using your existing modem.
All operating modes allow you to connect your devices through WLAN or LAN to the product.
The voltage to the product is supplied by the mains socket, where the product is plugged in.
)RUVDIHW\DQGFRPSOLDQFHUHDVRQVWKHSURGXFWPXVWQRWEHFRQYHUWHGRUPRGL¿HGLQDQ\ZD\
If you use the product for other purposes than those described above, the product may be dam-
DJHG0RUHRYHULPSURSHUXVHLQYROYHVULVNVVXFKDVVKRUWFLUFXLWV¿UHHOHFWULFVKRFNVHWF
Please read the operating instructions carefully and do not discard them. Please include these
operating instructions when you pass the product on to a third party.
This product complies with the applicable national and European Regulations. All names of
companies and products are the trademarks of the respective owners. All rights reserved.
Package contents
• WLAN
Repeater
AC1200
• RJ45
cable
• Operating
instructions
Latest operating instructions
Download the latest operating instructions via the link www.conrad.com/downloads
or scan the QR code shown here. Follow the instructions on the website.
Symbols explained
The lightning symbol inside a triangle is used when there is a potential risk of per-
sonal injury, such as electric shock.
An exclamation mark in a triangle indicates important steps in these operating in-
structions which should be absolutely observed.
7KHDUURZV\PEROLQGLFDWHVVSHFL¿FWLSVDQGDGYLFHRQRSHUDWLRQ
Safety instructions
Please read the operating instructions carefully and pay particular attention
to the safety instructions. We do not assume liability for any injuries/mate-
rial damages resulting from failure to observe the safety instructions and the
information in these operating instructions regarding the proper use of the
product. Furthermore, in such cases, the warranty/guarantee will be null and
void.
• The product design complies with protection class II. Only a standard mains sock-
et connected to the public supply may be used as the power source for the device.
• If the product is damaged, do not touch it; there is a danger to life from electric
shock!
Switch off the mains voltage to the mains socket to which the power adapter is
connected (e.g., switch off at the corresponding circuit breaker or remove the safe-
ty fuse and then switch off the corresponding RCD). Now disconnect the power
adapter from the socket and take the product to a specialized workshop.
• Check the product for damage before each use!
• If you detect any damage, DO NOT connect the product to the mains supply!
Danger to life!
• The product is only suitable for dry, enclosed indoor areas. Don’t let it get damp or
wet; never handle it, if your hands are wet!
There is a risk of a life-threatening electric shock!
• Protect the product from extreme temperatures, direct sunlight, strong vibrations,
high humidity, moisture, combustible gases, vapours and solvents.
