This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com). All rights
including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication
represents the technical status at the time of printing.
Copyright 2018 by Conrad Electronic SE.
*1697435_1697437_v1_0818_02_dh_m(2)_en
PWR1
PWR2
• Connect the 6-pin terminal block to the terminal input (4).
•
Connect one end of the terminal power supply leads (not
included) to PWR1 or PWR2 on the terminal block, and
connect the other end to the power supply.
• The power leads should be wired to the 6-pin power
terminal block matching polarities as marked.
•
Check the LED
PWR1 / PWR2
(1) on the front panel to make sure that any powered switches
are receiving power.
c) Place on DIN Rail
•
The DIN rail has to comply with EN 55022 (overall width 3.5 cm, overall height 0.75 cm). The
roduct may not be installed on any other mounting rails!
•
Place the product on the DIN rail and secure it in place.
d) Network Cable Connection
• Use suitable network cables to connect devices and computers to the switch ports.
• All network ports supports auto uplink, which means that no crosslink cables are necessary
to connect multiple network switches.
• Make sure the cables are not bent or crushed.
• We recommend to mark the network cables with suitable adhesive labels or other devices.
This will allow you in case of a fault to know perfectly which connections need to be checked.
Operation
a) DIP Switches (Alarm Control)
•
Switch 1 to 8 (ports 1 to 8). If these DIP switches are ON,
Alm
LED
(6) will activate if a network connection is severed.
•
Switch 9 (power inputs
PWR1 / PWR2). Alm
LED
(6) will turn
ON if
PWR1 or PWR2 fails.
b) Alarm Relay
•
The switch has a single 24 V/DC, 1 A alarm relay output, and can be set to trigger when a
network connection is severed a source of
power (
PWR1 / PWR2) fails or both.
• Alm
LED
(6) will blink and the alarm relay will trigger a few seconds later.
PWR1
PWR2
ALM
•
To deactivate the alarm, set the related DIP switch to
the OFF position.
•
To reactivate the alarm, set the related DIP switch to
the ON position after the alarm conditions have been
removed.
c) LED Indicators
LED
Colour
Status
Description
PWR1 / PWR 2
Green
ON
Receiving power
Green
OFF
No power received
Alm
Red
ON
Port link down or power failure
Red
OFF
No event
SFP
Green
ON
SFP connected
Green
OFF
No SFP connected
Green
Flashing
Network activity
Link/Act
Green
ON
Link active
Green
OFF
Link inactive
Green
Flashing
Network activity
Port speed
Amber
ON
Item No. 1697435: 1000 Mbit/s
Item No. 1697437: 100 Mbit/s
Amber
Flashing
Item No. 1697435: 10/100 Mbit/s
Item No. 1697437: 10 Mbit/s
Care and Cleaning
•
Disconnect the product from the mains before each cleaning.
•
Do not use any aggressive cleaning agents, rubbing alcohol or other chemical solutions as it
can cause damage to the housing and malfunctioning.
•
Clean the product with a dry, fibre-free cloth.
Disposal
Electronic devices are recyclable waste and must not be disposed of in the
household waste. At the end of its service life, dispose of the product in accordance
with applicable regulatory guidelines.
You thus fulfill your statutory obligations and contribute to the protection of the environment.
Technical Data
Specification
Item No. 1697435
Item No. 1697437
Input voltage
2x (12 - 24 V/DC) via removable
6-pin terminal block
2x (12 - 24 V/DC) via removable
6-pin terminal block
Output relay (alarm) 24 V/DC, 1A
24 V/DC, 1A
Power consumption
max. 8 W
max. 8 W
MAC address
4 K
4 K
Ports
6 x RJ45 (Gigabit)
2 x SFP (Gigabit)
6 x RJ45 (Fast Ethernet)
2 x SFP (Gigabit)
Buffer memory
4 Mb
4 Mb
IEEEE
IEEE 802.3 – 10BaseT
IEEE 802.3u - 100BaseTX
IEEE 802.3ab - 1000BaseT
IEEE 802.3z 1000 Base SX/LX
IEEE 802.3x - Flow Control
IEEE 802.3 10BaseT
IEEE 802.3u 100BaseTX
IEEE 802.3z 1000 Base SX/LX
IEEE 802.3x - Flow Control
EMI
FCC Class A Part 15, VCCI
Class A
FCC Class A Part 15, VCCI
Class A
EMS
EN61000-4-2 (ESD)
EN61000-4-3 (RS)
EN61000-4-8
N61000-4-2 (ESD)
EN61000-4-3 (RS)
EN61000-4-8
IEC
IEC60068-2-27 (shock),
IEC60068-2-32 (freefall),
IEC60068-2-6 (vibration)
IEC60068-2-27 (shock),
IEC60068-2-32 (freefall),
IEC60068-2-6 (vibration)
Filtering/forwarding
rates
11.904 Mpps
3.87 Mpps
RJ45 transmission
10 BaseT Cat. 3, 4, 5 UTP/STP
100 BaseTX Cat. 5 UTP/STP
1000 BaseT Cat. 5E UTP/STP
10 BaseT Cat. 3, 4, 5 UTP/STP
100 BaseTX Cat. 5 UTP/STP
SFP transmission
62.5/125 μm Multi Mode Fiber
optic cable, max. 220 m
50/125 μm Multi Mode Fiber
optic cable, max. 550 m
9/125 μm Single Mode Fiber
optic cable
62.5/125 μm Multi Mode Fiber
optic cable, max. 220 m
50/125 μm Multi Mode Fiber
optic cable, max. 550 m
9/125 μm Single Mode Fiber
optic cable
LED indicators
PWR1, PWR2, Alm, 1000M,
Link/Act
PWR1, PWR2, Alm, 10/100M,
Link/Act
Ingress protection
rating (housing)
IP30
IP30
Mounting
DIN-rail
DIN-rail
Operating
Temperature
-40 to +70 °C, 5 – 95 % relative
humidity (non-condensing)
-40 to +70 °C, 5 – 95 % relative
humidity (non-condensing)
Storage
temperature
-40 to +85 °C, 5 – 95 % relative
humidity (non-condensing)
-40 to +85 °C, 5 – 95 % relative
humidity (non-condensing)
Dimensions
(H x W x D)
55 x 120 x 108 mm
55 x 120 x 108 mm
Weight
0.56 kg
0.57 kg