manualshive.com logo in svg

Renishaw UCC MMI-2, Installation Manual, Page: 24 / 30

Share
Download
Renishaw UCC MMI-2 Installation Manual Download Page 24

USB connection (USB type B)

NOTE: 

UCCsuite should be installed before connecting the UCC MMI-2.

This is a standard USB type B connector providing the communication connection between the UCC MMI-2 and the PC hosting the application

software.

The host PC is recommended to have a dedicated USB connection to the UCC MMI-2.

Communication to a PC will be via a standard USB-A to USB-B cable using the USB 2.0 protocol supporting up to full-speed mode.

A 5 m USB cable is provided for this link as part of the UCC MMI-2 kit. Other lengths may be used; the maximum being 5 m which is governed

by the generic specification for USB connections.

When the UCC MMI-2 is connected to the PC and power applied to the unit, Windows will automatically detect the new hardware and start

the Windows hardware installation wizard.

The Windows hardware installation wizard will automatically identify the correct driver for the UCC MMI-2. This driver is located on the

UCCsuite software download.

UCC MMI-2 installation guide

www.renishaw.com

 

 

Issued 08 2020

24

Summary of Contents for UCC MMI-2































Reviews:

No comments