background image

2

Changes to equipment

Renishaw reserves the right to change specifications without 
notice.

Warranty

Equipment requiring attention under warranty must be returned 
to our supplier. No claims will be considered where equipment 
has been incorrectly installed or misused, or where repairs or 
adjustments have been attempted by unauthorised persons. 
Prior consent must be obtained in instances where Renishaw 
equipment is to be substituted or omitted. Failure to comply with 
this requirement will invalidate the warranty.

WEEE directive

The use of this symbol on Renishaw products and/or 
accompanying documentation indicates that the product should 
not be mixed with general household waste upon disposal. It is 
the responsibility of the end user to dispose of this product at 
a designated collection point for waste electrical and electronic 
equipment (WEEE) to enable reuse or recycling. Correct 
disposal of this product will help to save valuable resources and 
prevent potential negative effects on the environment. For more 
information, please contact your local waste disposal service or 
Renishaw distributor.

Care of equipment

Summary of Contents for Equator Gauge Checker





















Reviews: