Renfert 14520000, Instruction Manual

Page: 6 / 10

- 2 - EN
3.2 Safety Information
‡ 7KH
Vario E is an electrical device
with potential hazards. This unit
may only be locked and used by
authorized specialist personnel
after an examination with regard to
conformity with applicable national
standards.
‡ %HIRUHVWDUWLQJWKHXQLWFRPSDUH
the information on the nameplate
ZLWKWKHVSHFL¿FDWLRQVRI\RXUORFDO
power supply.
‡ 'RQRWRSHUDWHWKHXQLWZLWKGDP
-
aged power cords or other defects.
‡ 'XULQJRSHUDWLRQDOZD\VXQUROOWKH
power cord (overheating hazard in
case of a short circuit).
‡ /LTXLGZD[HVFDQFDXVHEXUQV'R
not move the unit during operation!
‡ 'XULQJRSHUDWLRQWKHZD[SRWVDUH
heated up to their rims. Improper
use or handling can result in burns
even approx. within 30 minutes after
power off.
‡ 7KH
Vario E is designed to be
used exclusively in conjunction
with commercially available dental
waxes. Never use the unit to heat
other types of materials!
‡ 3OHDVHQRWH2YHU¿OOHGSRWVFDQ
spill over!
‡ 'RQRWXVHWKLVGHYLFHZLWKPDWH
-
ULDOVZKRVHÀDVKSRLQWLVEHORZ
175°C (347°F). Keep away any
ÀDPPDEOHPDWHULDOVIURPWKHKRW
surface of device.
‡ 'RQRWULQVHRUGLSLQD]
-
ardous voltage can cause electric
shock!
‡ ,WLVWKHUHVSRQVLELOLW\RIWKHRSHUD
-
tor that national regulations during
operation and regarding a repeated
VDIHW\LQVSHFWLRQRIHOHFWULFDOHTXLS
-
ment are complied with.
For Germany these are BGV A3 in
relation with VDE 0701-0702.
3.3 Liability Exclusion
Renfert GmbH shall be absolved from all
claims for damages or warranty if:
‡ 7KHSURGXFWLVHPSOR\HGIRUDQ\
purposes other than those cited in
WKHRSHUDWLQJLQVWUXFWLRQV
‡ 7KHSURGXFWLVDOWHUHGLQDQ\ZD\
other than those alterations de-
scribed in the operating instruc-
WLRQV
‡ 7KHSURGXFWLVUHSDLUHGE\RWKHU
than an authorized facility or if any
but Renfert OEM parts are em-
SOR\HG
‡ 7KHSURGXFWFRQWLQXHVWREHHP
-
ployed, despite obvious safety
IDXOWV
‡ 7KHSURGXFWLVVXEMHFWHGWRPH
-
chanical jarring or is dropped.
4. Operating Elements
(Figure 1a+1b)
A) On/Off switch
% :D[SRWVHOHFWLRQEXWWRQ
& /('LQGLFDWRUIRUWKHVHOHFWHGZD[SRW
>>Operation indicator = green
>> Warm-up phase = red
D) Set-point temperature increase
E) Set-point temperature decrease
F) Setpoint/actual temperature display
* :D[SRW
H) Lid
I) Power cord
5. Commissioning /
Operation
5.1 Switching the Unit On
1. Connect the Vario E to the mains power
outlet (Figure 2).
2. Open lid (H). The lid can be locked in
place at a 120° angle (Figure 3).
$GGWKHZD[HVWREHKHDWHGWRWKHSRWV