manualshive.com logo in svg

REnex Technology R-001-0003-400, User Manual, Page: 8 / 25

Share
Download
REnex Technology R-001-0003-400 User Manual Download Page 8

 
 

ZcoRE3-2400_User_Manual_V1.0

Technical Parameters 

2.

 

Table 2.1 Technical Parameters of ZcoRE3-2400/ZcoRE3(20)-2400 

Radio Characteristics 

RF Frequency Band 

2.4 ~ 2.4835GHz 

Number of Channels 

16 channels       

Channel Spacing 

5 MHz 

RF Data Rate 

250 kbps 

Modulation OQPSK 

Duplex TDD 

Maximum E.R.P. 

1 (0 dBm) ~ 60 mW (18 dBm)

 

Receiver Sensitivity 

-95 dBm at 10

-3

 BER

 

Receiver Classification 

Class 2 

Operating Range 

Up to 1 km in line-of-sight(18dBm)*

 

Network Protocol 

Zigbee & IEEE 802.15.4 compliant   

Operating Mode 

Mesh 

Error Detection 

CRC and ARQ 

Radio Type Approval 

CE:  

EN300-328

 

FCC:  

Part 15.247 

SRRC & Middle-East : 

(pending)

 

Intrinsic Safety Design 

UL C1D1 / ATEX T4   

Miscellaneous 

I/O Interface 

Serial TTL with universal socket: 2 x 20 pins with 1.27 mm 

I/O Option 

Two digital I/O; one analog I/O;   

RS-232(TTL) for optional modules (Bluetooth, GPS, GPRS and 

WiFi) 

Antenna Port Interface 

Chip antenna(0dBm,18dBm)/MMCX female(18dBm) 

Power Supply 

3.3 ±.3V 

Power Consumption 

Normal working mode: 

Tx:                                   

44 

mA | 230mA(18dBm)@ 3.3 V 

Rx:                                   

35 

mA | 35mA(18dBm)@ 3.3 V 

Sleep mode:                     

9 

uA | 9 uA(18dBm) @ 3.3 V 

Operating Temperature 

-40

o 

C to 

75

o 

C  

Humidity 

20% to 90% non-condensing 

Dimensions (L 

×

 W 

×

 H) 

46.5 mm x 26 mm x 10 mm 

Weight 

10 grams (0.35 ounce) 

 

*Depending on the interference environment.

2 

Summary of Contents for R-001-0003-400


























Reviews:

No comments