Renesas SDI Emulator System M32100T-EZ-E User Manual Download Page 15

Page: 15 / 44

( 13 / 42 )

Chapter 2. Preparation

This chapter describes the package components, the system configuration and the preparation for using this product for the
first time.

2.1 Terminology ................................................................................................................................ 14

2.2 Package Components ................................................................................................................... 15

2.3 System Configuration of the M32100T-EZ-E ............................................................................. 16

(1) JTAG Connection ................................................................................................................. 16

2.4 Name of Each Part ....................................................................................................................... 17

(1) Names and Functions of Parts on the Upper Panel ............................................................... 17

(2) Names and Functions of Parts on the Side Panel.................................................................. 19

(3) Names and Functions of Parts on the Front Panel ................................................................ 19

(4) Names and Functions of Parts on the Rear Panel ................................................................. 20

Summary of Contents for SDI Emulator System M32100T-EZ-E












































Search results

Summary of Contents for SDI Emulator System M32100T-EZ-E

Reviews:

Related manuals for SDI Emulator System M32100T-EZ-E

Brands by name

Popular brands

Renesas SDI Emulator System M32100T-EZ-E, User Manual

Search results

Summary of Contents for SDI Emulator System M32100T-EZ-E

Reviews:

Related manuals for SDI Emulator System M32100T-EZ-E

Brands by name

Popular brands