background image

H8S, H8SX Family E10A-USB Emulator 

Section 1   Connecting the Emulator with the User System 

R20UT0271EJ0100  Rev. 1.00 

 

Page 2 of 20 

May 13, 2011 

 

Table 1.1   Components of the Emulator 

Classi-
fication 

 
Component 

 
Appearance 

Quan-
tity 

 
Remarks 

Hard- 
ware 

Emulator box 

1 HS0005KCU01H: 

Depth: 65.0 mm, Width: 97.0 mm, 
Height: 20.0 mm, Mass: 72.9 g 

or 

HS0005KCU02H: 
Depth: 65.0 mm, Width: 97.0 mm, 
Height: 20.0 mm, Mass: 73.7 g 

 

User system interface 
cable 

1 14-pin 

type: 

Length: 20 cm, Mass: 33.1 g 

 USB 

cable 

Length: 150 cm, Mass: 50.6 g 

Soft- 
ware 

H8S/2427 E10A-USB 
and H8S/2425 E10A-
USB emulator setup 
program,  
H8S, H8SX Family 
E10A-USB Emulator 
User’s Manual,  
Supplementary 
Information on Using 
the H8S/2427, 
H8S/2427R, 
H8S/2425 group*, 
and  
Test program manual 
for HS0005KCU01H 
and HS0005KCU02H 

1 HS0005KCU01SR, 

 

 
 
 
HS0005KCU01HJ-H8S, 
HS0005KCU01HE-H8S,  
 
HS2427KCU01HJ, 
HS2427KCU01HE,  
 
 
 
 
HS0005TM01HJ, and 
HS0005TM01HE 
(provided on a CD-R) 

Note:  Additional document for the MPUs supported by the emulator is included. Check the target 

MPU and refer to its additional document. 

 

Summary of Contents for H8S/2400 Series































Reviews: