manualshive.com logo in svg

Renesas DA9213, User Manual

Share
Download
Renesas DA9213 User Manual Download Page 18

 

 

UM-PM-029 

 

DA9213, DA9214, and DA9215 Performance 
Boards 

  

User Manual 

Revision 2.0 

25-Feb-2022 

CFR0012 

18 of 37 

© 2022 Renesas Electronics 

At the top right of the configuration tab the interface indicator should display the same details as 
shown in 

Figure 8

. 

 

Figure 8: Top Right Interface Indicator 

Select the 

Start Device

 button to configure the software for standalone operation correctly. This 

enables control of the DA9214 in standalone mode. In this mode, DA9214 acknowledges all I

2

C 

commands, which does not always happen if it is in companion mode.  

For details please refer to the STAND_ALONE bit in the Datasheet 

[1]

. 

Synchronize the panel from the device, by pressing the icon (indicated by the red arrow in 

Figure 9

), 

the target voltages and all DA9214 parameters are updated to the content of the IC registers. 

 

Figure 9: Bottom Right Interface Indicator 

Enable the BUCKA converter by pressing on the BUCK_EN button in BUCKA Control, which is 
equivalent to writing 0x01 into the related bit, see 

Figure 10

. An increase in the current drawn from 

the external supply will occur. 

NOTE 

The quiescent current shown on the multi-meter may still be higher than expected. This is due to the missing 
configuration and connection of floating I/O ports and will be reduced as soon as they are correctly set. 

 

Summary of Contents for DA9213







































Reviews:

No comments

Brands by name

Popular brands

Load more brands