background image

2  |  16 

M0698.docx  |  

Rev 2.3  |  Modified on 29/09/2017

 

|  © Remote Control Technologies Pty Ltd  

 

 

DISCLAIMER 

 
© Remote Control Technologies Pty Ltd. 

 
 

■ 

No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the written 
permission of RCT.

 

 

■ 

Information provided in this manual is intended to be accurate and reliable. However, RCT assumes no responsibility for its use or 
infringements upon the rights of third parties that may result from its use.

 

 

■ 

All examples and diagrams shown in this manual are intended only as an aid to understanding the text, not to guarantee operation.  
RCT will accept no responsibility for actual use of the product based on these illustrative examples. 

 

■ 

Please contact your nearest RCT branch for more information concerning applications in life critical situations or high reliability. 

 

■ 

RCT

 

reserves the right to make changes to any product herein to improve reliability, function or design.  All specifications are 

subject to change without notice. 

 

 

 

Summary of Contents for Muirhead 11337

















Reviews: