background image

5

Warranty

The warranty conditions are listed in 
the "General terms and conditions".  
Please contact your contractual partner in 
the first instance.

Environmental 

protection and recycling

Disposing of packaging

All products are packed for transport 
in environmentally friendly materials. 
You can make a valuable contribution 
to reducing waste and sustaining raw 
materials by only disposing of packaging 
at approved collection points. 

Disposal of  
components

The manufacturing process for the units 
is subject to continuous quality control. 
Only high-grade materials are processed, 
the majority of which are recyclable. 
You can also contribute to environmental 
protection by only disposing of 
components in accordance with local 
regulations and in an environmentally 
safe manner, e.g. through authorised 
disposal and recycling specialists or at 
collection points.

Intended use  

  

The tanks are used for the storage of hot water. 
Any different or additional use shall be classed 
as non-intended use. The manufacturer/
supplier assumes no liability for damages arising 
from such use. The user bears the sole risk in 
such cases.
Intended use also includes working 
in accordance with the operating 
manual and installation instructions 
and complying with the maintenance 
requirements.

Description

The tanks are used for the storage of hot 
water. 
The tank volume can be adapted to your 
particular needs by connecting several 
tanks to form batteries.  
The tank is enamelled and has a double-
wound, smooth-pipe heat exchanger 
with an especially large heat exchanger 
surface area of 3.5m

2

.

In the inside tank a magnesium false 
anode is installed in accordance with 
DIN 4753. 
The insulation of the hot water storage 
tank EWS 300 is comprised of a 50 mm 
thick PUR insulation (CFC, HCFC and 
HFC free). 
The tank is encased in a foil casing 
(delivered separately for transport 
protection). 
A blank flange cover D180 is installed 
for the retrofitting of a finned tube heat 
exchanger or flange heating cartridge 
(legionella protection). 

Summary of Contents for EWS 300





















Reviews: