background image

6

RECHARGEABLE BATTERY

The charger is designed to use standard house-
hold 120 volt 60 Hz power

1. 

Plug cord from charger into charger base. 
(See Figure 1)

2.  Plug the charger into any standard 120 

Volt 60 Hz electrical outlet. Important: Do 
not charge by means of an engine genera-
tor or DC power source. Use only 120V 
AC.

3. 

Slide the charger onto the battery pack as 
shown in Figure 2. The LED will light up,  
Let the battery pack charge until red LED 
turns off.  After the initial charge, under 
normal usage, your battery pack should be 
fully charged in 3 to 9 hours.

4. 

Unplug charger. Remove the battery pack 
by sliding out (See Figure 3).

5. 

Place the battery pack in the tool and be 
certain that it is inserted fully into the tool 
cavity until it “clicks” into place.

The battery pack is not fully 
charged at the factory. Before 
attempting to charge the battery 
pack, thoroughly read all Safety 
Instructions.

Figure 1 - Plug Charger into Base

Figure 3 - Remove Charger

PROTECTIVE BATTERY 
TERMINAL CAP

A protective battery terminal cap is provided 
for use whenever the battery is out of the tool 
or charger. Remove cap before placing battery 
in charger or tool.

b. An extension cord must have adequate 

wire size (AWG or American Wire 
Gauge) for safety, and to prevent loss of 
power and overheating. The smaller the 
gauge number of the wire, the greater 
the capacity of the cable; that is, 16 
gauge has more capacity than 18 gauge. 
When using more than one extension to 
make up the total length, be sure each 
extension contains at least the minimum 
wire size.

CHART FOR MINIMUM WIRE SIZE (AWG) 
OF EXTENSION CORDS NAMEPLATE 
RATING AMPS – 0 – 10.0

SAFETY WARNINGS

3.     Do not expose charger to rain or snow.

4.  Use of an attachment not recommended 

or sold by Remington brand may result in 
a risk of fi re, electric shock, or injury to 
persons.

5. 

To reduce risk of damage to electric plug 
and cord, pull by plug rather than cord 
when disconnecting charger.

6. 

An extension cord should not be used un-
less absolutely necessary. Use of improper 
extension cord could result in a risk of fi re, 
electric shock or electrocution.
a. Two-wire cords can be used with 2-

wire or 3-wire extension cords. Only 
round jacketed extension cords should 
be used, and we recommend that they 
be listed by Underwriters Laboratories 
(U.L.). If the extension is to be used 
outside, the cord must be suitable for 
outdoor use. Any cord marked for 
outdoor use can also be used for indoor 
work. The letters “W” or “WA” on the 
cord jacket indicate that the cord is suit-
able for outdoor use.

Cord

Length

AWG Cord

Size

25 feet

18 AWG

50 feet

18 AWG

100 feet

16 AWG

150 feet

14 AWG

7.  Use only the supplied charger (P/N 

725-05031 

when charging. The use of any 

other charger could damage the battery or 
create a hazardous condition.

8. 

Use only one charger when charging.

9. 

Use only Remington 

725-05032

 

pack with

this product.

10.  Do not attempt to open the charger. There 

are no customer serviceable parts inside. If 
damaged, call 

the Customer Support

Department.

11.  DO NOT incinerate the battery pack even 

if they are severely damaged or completely 
worn out. The batteries can explode in a 
fi re.

12.  A small leakage of liquid from the battery 

pack cells may occur under extreme usage, 
charging, or temperature conditions. This 
does not indicate a failure.   However, if 
the outer seal is broken and this leakage 
gets on your skin:
•  Wash quickly with soap and water.
•  Neutralize with a mild acid such as 

lemon juice or vinegar.

•  If the battery liquid gets in your eyes, 

fl ush them with clean water for a mini-
mum of 10 minutes and seek immediate 
medical attention.

13.  DO NOT open or mutilate the batteries.  

Released electolyte is corrosive and may 
cause damage to the eyes and skit.  It may 
be toxic if swallowed.

MEDICAL NOTE: The liquid is a 
25-35% solution of potassium 
hydroxide.

1.     This manual contains important safety        

and opertaing instructions.

2.  Before using battery charger, read all 

instructions and cautionary markings on 
battery charger, battery pack, and product 
using battery pack.

CHARGING BATTERY

Figure 2 - Sliding Charger onto  Battery

To reduce the risk of injury, 
charge only Remington brand 
batteries. Other types of batter-
ies may burst causing personal 
injury and damage.

 CAUTION: 

             WARNING

Do not store or carry battery so that 
metal objects can contact exposed 
battery terminals. For example, 
do not place battery in aprons, 
pockets, tool boxes, product kit 
boxes, drawers, etc. with loose 
nails, screws, keys, jewelry  etc. 
without battery cap.  The battery 
or conductor may overheat and 
case burns

Summary of Contents for RM40BST













































Reviews: