Remington RM2520 Operator'S Manual Download Page 3

READ ALL INSTRUCTIONS BEFORE OPERATING

Read the instructions carefully. Be familiar with the controls and
proper use of the unit.

Do not operate this unit when tired, ill or under the influence of
alcohol, drugs or medication.

Children must not operate the unit. Teens must be accompanied
and guided by an adult. 

Inspect the unit before use. Replace damaged parts. Check for
fuel leaks. Make sure all fasteners are in place and secure.
Replace parts that are cracked, chipped, or damaged in any way. 

Only use the trimming line described in the 

Specifications

section

of this manual. Never use metal-reinforced line, wire, chain or
rope. These can break off and become dangerous projectiles. 

Be aware of risk of injury to the head, hands and feet.

Clear the area to be cut before each use. Remove rocks, broken
glass, nails, wire, string and other objects which may be thrown
or become entangled in the trimmer attachment. Clear the area
of children, bystanders and pets; keep them outside a 50-foot
(15 m) radius, at a minimum. Even then, they are still at risk from
thrown objects. Encourage bystanders to wear eye protection. If
you are approached, stop the unit immediately.

Squeeze the throttle control and check that it returns
automatically to the idle position. Make all adjustments or
repairs before using the unit.

WHILE OPERATING

Wear safety glasses or goggles that meet current ANSI
standards and are marked as such. Wear ear/hearing protection
when operating this unit. Wear a face or dust mask if the
operation is dusty.

Wear heavy long pants, boots, gloves and a long sleeve shirt. Do
not wear loose clothing, jewelry, short pants, sandals or go
barefoot. Secure hair above shoulder level.

OTHER SAFETY WARNINGS

Never store the unit with fuel in the tank, inside a building where
fumes may reach an open flame (pilot lights, etc.) or sparks
(switches, electrical motors, etc.).

Allow the engine to cool before storing or transporting. Be sure
to secure the unit while transporting.

Store the unit in a dry place, secured or at a height to prevent
unauthorized use or damage. Keep out of the reach of children.

Never douse or squirt the unit with water or any other liquid.
Keep handles dry, clean and free from debris. Clean after each
use, see 

Cleaning and Storage

instructions.

Keep these instructions. Refer to them often and use them to
instruct other users. If you loan this unit to others, also loan
them these instructions.

SAVE THESE INSTRUCTIONS

SAFETY WARNINGS FOR GAS UNITS

Store fuel only in containers specifically designed and approved
for the storage of such materials.

Always stop the engine and allow it to cool before filling the
tank. Never remove the fuel tank cap or add fuel when the
engine is hot. Always loosen the fuel tank cap slowly to relieve
any pressure in the tank before fueling.

Always mix and add fuel in a clean, well-ventilated outdoor area
where there are no sparks or flames. DO NOT smoke.

Never operate the unit without the fuel cap securely in place.

Avoid creating a source of ignition for spilled fuel. Wipe up any
spilled fuel from the unit immediately, before starting the unit.
Move the unit at least 30 ft. (9.1 m) from the fueling source and
site before starting the engine. DO NOT smoke.

Never start or run the unit inside a closed room or building.
Breathing exhaust fumes can kill. Operate this unit only in a well
ventilated outdoor area.

The trimmer attachment shield must always be in place while
operating the unit. Do not operate unit without both trimming
lines extended, and the proper line installed. Do not extend the
trimming line beyond the length of the shield.

This unit has a clutch. The cutting head remains stationary when
the engine is idling. If it does not, take the unit to a qualified
service dealer for an adjustment.

Adjust the handle to provide the best grip.

Be sure the trimmer attachment is not in contact with anything
before starting the unit.

Use the unit only in daylight or good artificial light.

Avoid accidental starting. Be in the starting position whenever
pulling the starter rope. The operator and unit must be in a stable
position while starting. Refer to 

Starting and Stopping

.

Use the right tool. Only use this tool for its intended purpose.

Always hold the unit with both hands when operating. Keep a
firm grip on both handles or grips.

Keep hands, face, and feet away from all moving parts. Do not
touch or try to stop the trimmer attachment when it rotates.

Do not touch the engine, gear housing or muffler. These parts get
extremely hot from operation, even after the unit is turned off.

Do not operate the engine faster than the speed needed to cut, trim
or edge. Do not run the engine at high speed when not cutting.

Always stop the engine when cutting is delayed or when walking
from one cutting location to another.

If you strike or become entangled with a foreign object, stop the
engine immediately and check for damage. Do not operate
before repairing damage. Do not operate the unit with loose or
damaged parts.

Turn the engine to off and disconnect the spark plug for
maintenance or repair.

Use only original equipment manufacturer (OEM) replacement
parts and accessories for this unit. These are available from your
authorized service dealer. Use of any other parts or accessories
could lead to serious injury to the user, or damage to the unit,
and void the warranty.

Keep the unit clean of vegetation and other materials that may
become lodged between the cutting head and shield.

To reduce fire hazard, replace a faulty muffler and spark arrestor.
Keep the engine and muffler free from grass, leaves, excessive
grease or carbon build up.

• IMPORTANT SAFETY INSTRUCTIONS •

WARNING:

When using the unit, all safety rules must be

followed. Please read these instructions before operating
the unit in order to ensure the safety of the operator and any
bystanders. Please keep these instructions for later use.

WARNING:

Gasoline is highly flammable and its vapors

can explode if ignited. Take the following precautions:

3

Summary of Contents for RM2520

























































Reviews: