Reliable Equipment PDY-510 Operator'S Manual Download Page 1

1

DISTRIB

DISTRIB

DISTRIB

DISTRIB

DISTRIBUTED BY

UTED BY

UTED BY

UTED BY

UTED BY

OPERA

OPERA

OPERA

OPERA

OPERAT

T

T

T

TORS’

ORS’

ORS’

ORS’

ORS’

     

GUIDE

GUIDE

GUIDE

GUIDE

GUIDE

PDY-510  Manual 

10

-1

7

RELIABLE EQUIPMENT & SERVICE CO., INC.

301  Ivyland Road •  Warminster,  PA  18974  •  USA

Phone: 215-357-3500  •  Fax: 215-357-9193

MODEL: __________________________________

MAX. PRESSURE: _________________________
SERIAL NO.:  ______________________________
YEAR:  ___________________________________

NOTICE

NOTICE

NOTICE

NOTICE

NOTICE

Sizes,  weights  and  tool

specifications  listed  in

this manual are subject

to change without notice.

Please consult factory for

information and updates.

W

W

W

W

WARNING

ARNING

ARNING

ARNING

ARNING

All  information  found  in  this  guide

  must be read and understood before

 use or testing of this tool.

Failure to read and understand these warnings

and safe handling instructions could result in

severe personal injury and or death

.

12 TONS OF FORCE

ACCEPTS “U” TYPE DIES

PDY-510

DOUBLE ACTING HYDRAULIC

COMPRESSION TOOL

DIRECT CONNECT

Summary of Contents for PDY-510

















Reviews: