background image

1

FCC STATEMENT

 

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
 

(1)  This device may not cause harmful interference, and 

 

(2)   This device must accept any interference received, including interference that may cause  

undesired operation.

NOTE:  This equipment has been tested and found to comply with the limits for a Class B digital Device, pursuant to Part 15 of the 

FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the  

instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will 

not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can 

be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of 

the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

 

Summary of Contents for AirShip Wireless


















Reviews: