Rekluse CoreManual TorqDrive Installation & User Manual Download

Page: 2 / 20

Pg. 2

Doc ID: 191-7113080A

Doc Rev: 080118

TABLE OF CONTENTS

OVERVIEW ................................................................................... 2

INSTALLATION TIPS .................................................................... 3

TOOLS NEEDED........................................................................... 3

INCLUDED PARTS ....................................................................... 4

BIKE PREP & DISASSEMBLY ...................................................... 5

INSPECT THE DAMPERS ........................................................ 7

INSTALL HUBS ............................................................................. 8

INSTALL THE CLUTCH PACK ................................................... 10

PRESSURE PLATE INSTALLATION .......................................... 13

MAINTENANCE........................................................................... 17

Clutch wear ............................................................................. 17

Clutch parts ............................................................................. 18

Preventive Maintenance .......................................................... 18

NEED ADDITIONAL HELP? ........................................................ 20

OVERVIEW

•

This kit replaces the OE (Original Equipment) or “stock” core

clutch components including the center clutch hub and
pressure plate with high-quality billet components designed
for optimal operation specific to your bike.

•

All 8 OE friction disks will be replaced with Rekluse

TorqDrive

Frictions, and all OE steel drive plates will be

replaced with Rekluse TEC drive plates.

•

All 6 of the OE drive pins will be reinstalled.

•

If you install this product for a customer or another person,

instruct them to read the

Safety Information

document and

the

Installation and User Guide

before operating the bike

with the product.

Summary of Contents for CoreManual TorqDrive





















Search results

Summary of Contents for CoreManual TorqDrive

Reviews:

Related manuals for CoreManual TorqDrive

Brands by name

Popular brands

Rekluse CoreManual TorqDrive, Installation & User Manual

Search results

Summary of Contents for CoreManual TorqDrive

Reviews:

Related manuals for CoreManual TorqDrive

Brands by name

Popular brands