manualshive.com logo in svg

Regency Plateau PTO30-LP, Owners & Installation Manual, Page: 21 / 32

Share
Download
Regency Plateau PTO30-LP Owners & Installation Manual Download Page 21

Regency Plateau™ PTO30 Outdoor Gas Fireplace

21

INSTALLATION

VOLCANIC STONE INSTALLATION ON BURNER 

OUTDOOR VOLCANIC STONE BURNER PACKAGES

Unit

Volcanic Stones

Ivory/Tan

Volcanic Stones

Slate/Grey

HZO42/HZO42 (AUS)

35 stones w/3lbs glass

35 volcanic stones  w/3lbs glass

PTO30 */ Plateau Series

50 stones w/5lbs glass

50 volcanic stones w/5lbs glass

PTO60

100 stones w/10lbs glass

100 stones w/10lbs glass

NOTE: 

   

*

  Basalt Volcanic stones are measured by weight not quantity. Each bag contains 15lbs of stones, however the exact quantity  and 

size will vary.

                Size varies between 2" - 3".

Volcanic Glass Crystals

For the PTO30, PTO60 

& Plateau Series only

Volcanic Stones Ivory /Tan + Glass Crystals

For the HZO42 & HZO42AUS

only

Volcanic Stones Slate /Grey + Glass Crystals

For the HZO42 & HZO42AUS

only

Evenly spread the glass crystals and volcanic stones over the burner. Ensure the stones do not overlap too much as this will effect the fl ame 
pattern.

IMPORTANT NOTE:

Only the supplied approved Volcanic Stones are to be used with these fi replaces.  Use of any other type of stones can alter the unit's performance, 
any damage caused by the use of any unapproved glass or stones will not be covered under warranty.

When using Volcanic Stones DO NOT cover burner ports or pilot light that lead to pilot fl ame. Ensure the stones do not overlap excessively as this 
will effect the fl ame pattern.

Summary of Contents for Plateau PTO30-LP

































Reviews:

No comments