Regency PANORAMA P33E Owners & Installation Manual Download Page 34

Page: 34 / 64

Regency® P33E-10 Zero Clearance Direct Vent Gas Fireplace

installation

Each Kit contains one LPG

Conversion Kit

LPG Conversion Kit Contains:

Qty. Part #

Description

904-575

Burner Orifice #55

918-590

Decal "Converted to

LPG"

908-528

Red "LPG" label

904-529

5/32" Allen Key

910-101

LPG Injector

(Pilot Orifice)

1 911-011

Stepper motor

919-467

Instruction Sheet

Conversion from NG to LPG

P33E-10 using SIT 885 NOVA Gas Valve

THIS CONVERSION MUST BE DONE BY A QUALIFIED GAS FITTER IF IN DOUBT DO NOT DO THIS CONVERSION!!

Installation of the LPG

Conversion Kit:

Shut off the gas and electrical supply.

Remove faceplate (if installed).

Remove the safety screen and glass

door.

Release the two hooks from the

bottom of the glass door.

Swing the door out 45 degrees from

the bottom - then lift up and out.

Remove the logs, embers, and brick

panels (if installed).

Remove the 2 screws, push Burner

Assembly to the left and lift out.

) Remove the 2 screws holding the Burner

Assembly to the firebox base. Push the

Burner Assembly to the left and lift out.

Unscrew the pilot orifice with the Allen

key and replace with the LPG pilot orifice

in the kit and replace pilot cap.

Remove burner orifice with a 1/2"

wrench and discard. Use another

wrench to hold on to the elbow behind

the orifice.

Burner Orifice

Remove pilot retainer clip with pliers and

pull off the pilot cap to expose pilot orifice.

Clip

Pilot Cap

Reinstall new burner orifice LPG

stamped #55 and tighten.

Remove regulator and discard. Install

the Hi/Lo pressure regulator onto the
valve with 2 screws as shown below.

Installer Notice:

These instructions must be

left with the appliance.

10)

Attach the label “This unit has been

converted to LPG” near or on top of the

serial # decal.

11)

Replace yellow “NG” label with red

“LPG” label.

12)

Reverse steps 4 through 1

13)

Check for gas leaks.

14)

Check inlet and outlet pressures.

15)

Check operation of flame control.

919-467

10.20.14

CONVERSION FROM NG TO LP

For P33E-10 Using SIT 885 NOVA Gas Valve

Summary of Contents for PANORAMA P33E

































































Search results

Summary of Contents for PANORAMA P33E

Reviews:

Related manuals for PANORAMA P33E

Brands by name

Popular brands

Regency PANORAMA P33E, Owners & Installation Manual

Search results

Summary of Contents for PANORAMA P33E

Reviews:

Related manuals for PANORAMA P33E

Brands by name

Popular brands