Regency P42-LP3 Owners & Installation Manual Download

Page: 44 / 44

Installer: Please complete the following information

Dealer Name & Address: ______________________________________________

__________________________________________________________________

Installer: ___________________________________________________________

Phone #: ___________________________________________________________

Date Installed: ______________________________________________________

Serial No.: _________________________________________________________

Printed in Canada

Regency fireplace products are designed

with reliability and simplicity in mind. In

addition, our internal Quality Assurance

Team carefully inspects each unit

thoroughly before it leaves our

door.

Fireplace Products International

Ltd. is pleased to extend this Lim-

ited Lifetime Warranty to the original

purchaser of a Regency Product.

See the inside back cover for details.

Regency and Panorama are trademarks of FPI Fireplace Products International Ltd.

Register your Regency online at

http://www.regency-fire.com

Summary of Contents for P42-LP3













































Search results

Summary of Contents for P42-LP3

Reviews:

Related manuals for P42-LP3

Brands by name

Popular brands

Regency P42-LP3, Owners & Installation Manual

Search results

Summary of Contents for P42-LP3

Reviews:

Related manuals for P42-LP3

Brands by name

Popular brands