Regency Grandview G800C Owners & Installation Manual Download Page 74

Page: 74 / 92

Grandview® G800C Gas Fireplace

installation

920-133

06.24.19

FAN INSTALLATION

8. Remove centre screw and loosen screw on light assembly as shown.

9. Pivot light assembly out to 90

10. Remove eight (8) screws from fi rebox fl oor access panel.

11. Lift out panel with light assembly and set aside, be careful of light

assembly wiring.

12. Manoeuvre fan assembly onto pins on unit fl oor via fan access opening.

13. Connect the fan to the DFC and ground—follow Steps 5-7 from the

previous page.

TO REMOVE THE FAN

Shut the power off.

2. Reverse the above instructions.

Note:

The bearings are lubricated for life. Do not lubricate

them. Make sure you vacuum the fan area on a regu-
lar basis.

IMPORTANT:

These fans collect a lot of dust from within your home. Ensure you

maintain these fan motors on a regular basis by vacuuming out the

fan blades and housing using a soft brush nozzle.

Diagram 7

Diagram 10

Diagram 8

Diagram 9

Fan Install After Unit Installation

The The fan may be installed after the unit has been installed and finished.

Ensure the unit is turned off and has cooled to room temperature.

1. Remove the screen, glass door, and bottom cover panel (see manual

for instructions).

2.  Remove any media already installed (logs, glass ,etc.) and set aside.
3.  Remove the log grate if installed.
4.  Remove the burner by removing 3 screws.
5.  Remove the ember media tray with 2 screws.

6. Remove the fan access panel by removing 8 screws.

7. Connect the 2 fan ground wires to the unit ground lug and secure

the fan speed control module with 2 screws (see steps 4-5 from
previous page). Tidy ground wires with provided plastic wire clip.

8. Install fan onto pins at the back right of the unit floor. Push down

on the front of the fan bracket to raise the back of the fan assembly
onto the pins.

9. Attach thermodisc cage to the bracket on the underside of the fan

access panel.

10. Reinstall all removed components by reversing steps 1-6.

11. Plug fan power cord into unit electrical outlet (see step 8 from previ-

ous page)

Summary of Contents for Grandview G800C





























































































Search results

Summary of Contents for Grandview G800C

Reviews:

Related manuals for Grandview G800C

Brands by name

Popular brands

Regency Grandview G800C, Owners & Installation Manual

Search results

Summary of Contents for Grandview G800C

Reviews:

Related manuals for Grandview G800C

Brands by name

Popular brands