Regency Grandview G800C Owners & Installation Manual Download Page 33

Page: 33 / 92

Grandview® G800C Gas Fireplace

| 33

installation

Nailing Flange
Tabs folded
forward

Mounting Tabs
folded forward

Mounting
Tab Folded
forward

Nailing Flange
folded forward

Framing

Face Plate

Top View

Install the Face Plate by resting the arms on the
Face Plate on top of the mounting tabs.

Adjust left and right to center the Face Plate.

NOTE: Do not to touch the Face Plate without
clean, soft, gloves. Dirt or oils can be transferred
onto the finish and become permanent.

Critical Finishing Gap

Faceplate - Finishing:

A 1/2” gap must be maintained on the sides of
the fireplace to allow the Face Plate to be in-
stalled and removed.

Do NOT finish past the front face of the fireplace.

Summary of Contents for Grandview G800C





























































































Search results

Summary of Contents for Grandview G800C

Reviews:

Related manuals for Grandview G800C

Brands by name

Popular brands

Regency Grandview G800C, Owners & Installation Manual

Search results

Summary of Contents for Grandview G800C

Reviews:

Related manuals for Grandview G800C

Brands by name

Popular brands