manualshive.com logo in svg

Regency Gas Insert E21-LP3, Owners & Installation Manual

Share
Download
Regency Gas Insert E21-LP3 Owners & Installation Manual Download Page 27

 Regency

®

 E21-3 Gas Fireplace Insert

27

INSTALLATION

1)

 

Attach the inner faceplate panel to the insert body using 4 screws 
in the locations shown below.

Diagram 1

Diagram 2

Diagram 3

Diagram 4

Diagram 5

2)

 

Connect the male end black and red fan switch wires to the wire 
connectors from the fan speed control.

3)

 

  

Connect the female ends of the ON/OFF switch - to the ON/OFF 
switch in the control box.

6)

 

Attach the 2 bottom louver hinges to the bottom fl ange on the 
fi rebox using 2 screws per hinge.

Diagram 6

Diagram 7

4)

   Tuck the wires into the clip to keep them away from the insert using 

the clip provided. Attach the clip to the rear of the faceplate to en-
sure that the wires do not touch the side of the unit. The power cord 
should be run behind the inner faceplate panel.

5)

        Install the on /off switch - fan speed control box to the left hand 

bottom leg of the inner faceplate.  Controls located on the left side.

LOW PROFILE FACEPLATE INSTALLATION

Summary of Contents for Gas Insert E21-LP3









































Reviews:

No comments

Brands by name

Popular brands

Load more brands