manualshive.com logo in svg

Regency Gas Insert E21-LP3, Owners & Installation Manual

Share
Download
Regency Gas Insert E21-LP3 Owners & Installation Manual Download Page 20

20

 Regency

®

 E21-3 Gas Fireplace Insert

INSTALLATION

Diagram 4

Diagram 5

6)

  Connect the ON/OFF switch wires by taking 

the black and red wires with the female ends 
and connecting them to the ON/OFF switch.

Diagram 3

faceplate panel.

9)

  Attach the brass trim to the faceplate by 

drilling a 1/8" hole through into the faceplate 
using the hole in the trim as a guide.  Fasten 
the trim to the faceplate panels using the 
gold plated screws.  See diagram 4.

10)

 Attach the faceplate panels to the insert 

7)

  Tuck the wires into the faceplate to keep 

them away from the insert using the clip 
provided.  Attach the clip to the rear of the 
faceplate to ensure that the wires do not 
touch the side of the unit.  See diagram 3.

8)

  The power cord should be run behind the 

body using the 4 remaining black screws. 
See diagram 5.

11)

 Push the logo plate into the two holes in 

the bottom left corner of the faceplate. See 
diagram 4.

FACEPLATE & TRIM 

INSTALLATION

1)

  Lay the faceplate panels fl at, face down on 

something soft so they don't scratch.

2)

  Take the top faceplate and align the holes 

in it with the holes in the side panels. Using 
the screws provided, attach from the top of 
the panel (the holes in the top panel are 
slightly larger than the holes in the side 
panel to facilitate easier installation). See 
diagram 1.

  

 Hint:  Don't tighten the trim to the bottom of 

the faceplate side panels with the screws 
provided.  See diagram 1.

Diagram 1

Diagram  2

4)

  Place the trim on the assembled faceplate 

panels, aligning the wire connections from 
the switches with the notch on the left side 
panel.

5)

  Connect the fan switch wires by taking the 

black and red wires with the male ends (in 
the grey harness) and connect them with 
the wire connectors from the fan speed 
control.

Hearth Trim Option: Hearth Trim is an option 
that can be used to fi nish off  the installation 
when the bottom of the fi replace is higher than 
the hearth or to raise the fi replace. Lay the face-
plate side panels fl at, face down on something 
soft so they don't scratch.  Attach the Hearth 
Trim to the bottom of the faceplate side panels 
with the screws provided.  See Diagram 2.  Now 
attach the assembled pieces to the insert body.

3)

  Using the connectors provided, join the left 

side trim (with the ON/OFF switch) to the 
top trim. See diagram 2.  Connect the right 
side trim to the top trim.

Summary of Contents for Gas Insert E21-LP3









































Reviews:

No comments

Brands by name

Popular brands

Load more brands