background image

14

Regency

®

 F39 Room Sealed Freestanding Gas Stove

Diagram 11: The upper half of the fl ashing is 

installed under the roofi ng material and not 

nailed down until the chimney is installed. This 

allows for small adjustments.

4)

  Assemble the desired lengths of black pipe 

and  elbows necessary to reach from the 
appliance adaptor up though the Round 
Support Box. Insure that all pipes and elbow 
connections are in the fully twist-locked 
position and sealed.

5)

  Cut a hole in the roof centred on the small 

drilled hole placed in the roof in Step 2. The 
hole should be of suffi cient size to meet 
the minimum requirements for clearance 
to combustibles of 1-1/4". Slip the fl ashing 
under the shingles (shingles should overlap 
half the fl ashing) as per diagram 11.

Diagram 12

7)

  Ensure fl ue is vertical and secure the base 

of the fl ashing to the roof with roofi ng rails, 
slide storm collar over the pipe section and 
seal with a mastic.

8)

  Install the vertical termination cap by twist 

locking it.

 Notes:

 a)

  For multistorey vertical installations, a 

Ceiling Fire stop (Part # 963) is required 
at the second fl oor, and any subsequent 
fl oor. Diagram 13.  The opening should 
be framed to 10 " x 10" inside dimen-

6)

  Continue to assemble pipe lengths.

Note:  If an offset is necessary in the attic to 

avoid obstructions, it is important to 
support the fl ue pipe every 3 feet, to 
avoid excessive stress on the elbows, 
and possible separation.  Wall straps 
are available for this purpose.  See 
diagram 7. 

 
 

Galvanized pipe and elbows may be utilized 
in the attic as well as above the roofl ine.  
The galvanized fi nish is desirable above the 
roofl ine due to its higher corrosion resist-
ance.

 

Continue to add pipe sections through the 
fl ashing until the height of the fl ue cap meets 
the minimum height requirements specifi ed 
in diagram 12 or local codes.  Note that for 
steep roof pitches, the vertical height must 
be increased.  A poor draft, or down drafting 
can result from high wind conditions near 
big trees or adjoining roof lines, in these 
cases, increasing the fl ue height may solve 
the problem.

    Roof Pitch                   Minimum Flue Height

                                           Feet         Meters

fl at to 7/12 

      

0.61

over 7/12 to 8/12 

0.61

over 8/12 to 9/12 

0.61

over 9/12 to 10/12 

2.5 

0.76

over 10/12 to 11/12 

3.25 

0.99

over 11/12 to 12/12 

1.22

over 12/12 to 14/12 

1.52

over 14/12 to 16/12 

1.83

over 16/12 to 18/12 

2.13

over 18/12 to 20/12 

7.5 

2.29

Diagram 10

Diagram 9

Diagram 8

Diagram 7

Diagram 6

DURA-FLUE VERTICAL 

TERMINATION

1)

  Maintain the 1-1/4" clearances 

(air spaces) to combustibles 
when passing through ceil-
ings, walls, roofs, enclo-
sures, attic rafter, or other 
nearby combustible surfaces. 
Do not pack air spaces with 
insulation. Check page 9 for 
the maximum vertical rise 
of the fl uing system and the 
maximum horizontal offset 
limitations.

3)

  To install the Round Support Box/Wall Thim-

ble in a fl at ceiling, cut a 10 inch square hole 
in the ceiling centred on the hole drilled in 
Step 2. Frame the hole as shown in diagram 
10.

INSTALLATION

8)

  Slide the decorative wall thimble up to the 

wall surface being careful not to scratch 
the paint and attach with screws provided. 
Apply decorative brass or chrome trim if 
desired. See diagram  7.

2)

  Set the gas appliance in 

its desired location. Drop a 
plumb bob down from the 
ceiling to the position of the 
appliance fl ue exit, and 
mark the location where 
the fl ue will penetrate the 
ceiling. Drill a small hole 
at his point. Next, drop a 
plumb bob from the roof to 
the hole previously drilled 
in the ceiling, and mark the 

spot where the fl ue will penetrate the roof. 
Determine if ceiling joists, roof rafters or 
other framing will obstruct the fl uing system. 
You may wish to relocate the appliance or 
to offset, as shown in diagram 9 to avoid 
cutting load bearing members.

Summary of Contents for F39-LPG
































Reviews: