background image

24

 | 

Regency

®

 U39-12 ULTIMATE™ Freestanding Gas Stove

installation

Diagram 10

Diagram 9

Diagram 8

Diagram 7

Diagram 6

7.

  Install the Wall Thimble in the center of the 10" 

square and attach with wood screws.

8.

  Slide the decorative wall thimble up to the wall 

surface being careful not to scratch the paint and 
attach with screws provided. Apply decorative 
brass or chrome trim if desired. See diagram  
7.

Dura-Vent Vertical Terminations

3.

  To install the Round Support Box/Wall Thimble 

in a flat ceiling, cut a 10 inch square hole in 
the ceiling centred on the hole drilled in Step 
2. Frame the hole as shown in diagram 10.

Diagram 5

Note: If installing termination on a siding  covered 

wall, a vinyl siding standoff or furring strips must 
be used to ensure that the termination is not 
recessed into the siding. The four wood screws 
provided should be replaced with appropriate 
fasteners for stucco, brick, concrete, or other 
types of sidings.

5.

  Before  connecting  the  horizontal  run  of  vent 

pipe  to  the  vent  termination,  slide  the  black 
decorative wall thimble cover over the vent pipe, 
then slide the Wall Thimble over the vent pipe.

6.

  Slide the appliance and vent assembly towards 

the wall carefully inserting the vent pipe into 
the vent cap assembly. It is important that the 
vent pipe extends into the vent cap a sufficient 
distance  so  as  to  result  in  a  minimum  pipe 
overlap of 1-1/4 inches. Secure the connection 
between  the  vent  pipe  and  the  vent  cap  by 
attaching the two sheet metal strips extending 
from  the  vent  cap  assembly  into  the  outer 
wall of the vent pipe. Use the two sheet metal 
screws  provided  to  connect  the  strips  to  the 
pipe. Bend any remaining portion of the sheet 
metal strip back towards the vent  cap, so it will 
be  concealed  by  the  decorative  wall  thimble 
cover. See diagram 6.

4.

  If installing the vent termination to a wall with 

vinyl siding, the Vinyl Siding Standoff must be 
used. Attach the Vinyl Siding Standoff to the 
Horizontal Vent Termination, but first run a bead 
of  non-hardening  mastic  around  its  outside 
edges, so as to make a seal between vent cap 
and the standoff. Install the Vinyl Siding Standoff  
between the vent cap and the exterior wall and 
attach  with  the  four  wood  screws  provided. 
Seal around the Vinyl Siding Standoff on all 
four sides. Diagram 5.   

The arrow on the vent 

cap should be pointing up.

 Insure that the 

1-1/4" clearances to combustible materials are 
maintained. See diagram 5.

Below Grade Installation

If the Snorkel Termination must be installed below 
grade, i.e. basement application, proper drainage 
must be provided to prevent water from entering 
the Snorkel Termination. Refer to Dia. 4. Do not 
attempt to enclose the Snorkel within the wall, or 
any other type of enclosure.

Diagram 4

1.

  Maintain the 1-1/4" clearances 

(air spaces) to combustibles 
when passing through ceilings, 
walls,  roofs,  enclosures, 
attic  rafter,  or  other  nearby 
combustible  surfaces.  Do 
not  pack  air  spaces  with 
insulation.  Check  the  "Rigid 
Pipe Venting  Arrangements" 
section  for  the  maximum 
vertical  rise  of  the  venting 
system  and  the  maximum 
horizontal offset limitations.

2.

  Set  the  gas  appliance  in 

its  desired  location.  Drop  a 
plumb  bob  down  from  the 
ceiling to the position of the 
appliance flue exit, and mark 
the  location  where  the  vent 
will penetrate the ceiling. Drill 
a small hole at his point.

 

Next,  drop  a  plumb  bob  from  the  roof  to  the 
hole previously drilled in the ceiling, and mark 
the spot where the vent will penetrate the roof. 
Determine if ceiling joists, roof rafters or other 
framing  will  obstruct  the  venting  system. You 
may wish to relocate the appliance or to offset, 
as  shown  in  diagram  9  to  avoid  cutting  load 
bearing members.

Summary of Contents for U39-NG12





























































Reviews: