Regency Fireplace Products P48 Owners & Installation Manual Download Page 17 | Manualshive

Page: 17 / 44

background image

Regency P48 Zero Clearance Direct Vent Gas Fireplace

17

INSTALLATION

The P48 is approved for a maximum 35 ft. (10.6m) straight vertical, with
Simpson Dura-Vent Direct Vent GS vent systems for Propane and Natural
Gas, as per the diagram 3.

The shaded area in the diagram 3 shows all allowable combinations of straight
vertical and offset to vertical terminations with Simpson Dura-Vent Direct
Vent GS vent systems for Propane and Natural Gas. Maximum two 45

o

elbows allowed.

•

Vent must be supported at offsets

•

Firestops are required at each floor level and whenever passing
through a wall.

•

Maintain clearances to combustibles as listed on pages 6 to 9.

Diagram 3

«
...
15
16
17
18
19
...
»

Summary of Contents for P48













































Reviews:

No comments

Related manuals for P48

Brand: Majestic Pages: 44

Brand: Napoleon Pages: 16

ISOKERN Standard 36

Brand: EarthCore Pages: 12

Brand: Napoleon Pages: 120

Brand: Twin-Star International Pages: 28

Brand: wiking Pages: 4

Direct WDC-SEA-FP-TOP

Brand: Woodard Pages: 2

Brand: superior fires Pages: 5

Brand: Dimplex Pages: 18

Brand: Whalen Pages: 60

Brand: Desa Pages: 36

Brand: Lennox Pages: 4

Brand: Char-Broil Pages: 4

Contura C610 Style

Brand: Nibe Pages: 20

Brand: Heatmaster Pages: 4

Wood Burning Fireplace I100

Brand: Heatilator Pages: 52

Wood Burning Fireplace EL36 Series

Brand: Heatilator Pages: 52

Brand: Heatilator Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands