REED RG6S User Manual Download Page 12

12

0722-50323

RG6  Portable  Roll  Groover                     

 

 

 

                

REED Warranty

REED will repair or replace tools with any defects due to faulty materials or workmanship for one 

(1) year or five (5) years from the date of purchase, as applicable. This warranty does not cover 

part failure due to tool abuse, misuse, or damage caused where repairs or modifications have been 

made or attempted by non REED authorized repair technicians.This warranty applies only to REED 

tools and does not apply to accessories. This warranty applies exclusively to the original purchaser.

One (1) year warranty: Power units for pneumatic, electric, hydraulic and battery-powered tools have 

a one year warranty. This includes, but is not limited to REED pumps, universal pipe cutter motors, 

power drives, power bevel tools, threading machines, cordless batteries and chargers.

Five (5) year warranty: Any REED tool not specified under the one (1) year warranty above is war-

rantied under the REED five (5) year warranty.

NO PARTY IS AUTHORIZED TO EXTEND ANY OTHER WARRANTY. NO WARRANTY FOR 

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE SHALL APPLY. No warranty 

claims will be allowed unless the product in question is received freight prepaid at the REED fac-

tory. All warranty claims are limited to repair or replacement, at the option of REED, at no charge to 

the customer. REED is not liable for any damage of any sort, including incidental and consequential 

damages. This warranty gives you specific legal rights, and you may also have other rights which 

vary by state, province or country. 

  

Warranty Effective December 1, 2018

CAUTION: Safety reminders for a professional approach to tool selection and use.

   Proper maintenance of tools is critical to personal safety; worn tools should be repaired or replaced as required.

   Select the correct tool and tool size for the job. Never modify a tool to exceed its intended capacity.

   We recommend the Hand Tools Institute booklets for additional safety tips. Booklets are available from REED or the Hand Tools Institute.

0722-59200

 

1425 West 8th Street

  Erie, PA 16502 USA    

Phone: 

800-666-3691  or  +1 814-452-3691

    

Fax: 

+1 814-455-1697

    

[email protected]

www.reedmfgco.com

0722-50323

Summary of Contents for RG6S













Reviews: