REED R9900 Instruction Manual Download Page 8

reedinstruments

www

com

8

Pantone 534 Blue

Pantone 123 Yellow

Pantone 485 Red

Pantone 123 Yellow

Pantone 534 Blue

Black

Rich Black - 

20/20/20/100

Blue -  100/80/30/5

Yellow - 0/27/100/0

Red - 10/100/100/5

Yellow - 0/27/100/0

Blue -  100/80/30/5

Only if you REALLY need them:

Pantone 534 Blue -  100/80/30/5

Pantone 485 Red - 10/100/100/5

Pantone 123 Yellow - 0/27/100/

INSTRUMENTS

RH Calibration

The humidity sensor can be manually calibrated with the optional 33% 
and 75% salt solutions. It is recommended that the ambient condition to 
be at 25°C and at an stable humidity for the highest accuracy. To abort 
the calibration at any time, turn the meter off. Do not calibrate the humid

-

ity without the specified calibration salt otherwise it will cause permanent 
damage. Contact REED Instruments at info@reedinstruments for calibra

-

tion salt or for service.

Turn the meter on and plug the sensor probe into the 33% salt bottle. 
Hold down the “CAL” and “DP/WBT” button to initiate RH Calibration. 
“CAL” and the calibrating value of 33% (32.7% if at 25°C) will blink on 
the LCD along with the current temperature at the left. The meter is now 
calibrating and will finish when “CAL” and humidity stop blinking, which is 

about 60 minutes. 

After the 33% calibration is complete, plug the sensor probe into the 75% 
salt bottle. Press the “ENTER” button to initiate 75% calibration. “CAL” 
and the calibrating value of 75% (75.2% if at 25°C) will blink on the LCD 
along with the current temperature at the left. The meter is now calibrating 
and will finish when “CAL” and humidity stop blinking, which is about 60 

minutes.

To calibrate 33% only, press the “ESC” button when calibration is com

-

plete. To calibrate 75% only, press the “UP” or “DOWN” button after you 
press the “CAL” and “DP/WBT” buttons.

Software

This meter can link to a PC for logging and data analysis via the optional 
RS232 interface and software. The protocol is as follows: 
A. 9600 bps, 8 data bits, no parity.
B. Cxxxxppm:Txxx.xC(F):Hxx.x%:dxxx.xC(F):wxxx.xC(F) LRC CRLF 
  Description: $CO2:Air:RH:DP:WBT LRC CRLF 

www.

.com

[email protected]

1.800.561.8187

Summary of Contents for R9900











Reviews: