REED R9900 Instruction Manual Download Page 6

reedinstruments

www

com

6

Pantone 534 Blue

Pantone 123 Yellow

Pantone 485 Red

Pantone 123 Yellow

Pantone 534 Blue

Black

Rich Black - 

20/20/20/100

Blue -  100/80/30/5

Yellow - 0/27/100/0

Red - 10/100/100/5

Yellow - 0/27/100/0

Blue -  100/80/30/5

Only if you REALLY need them:

Pantone 534 Blue -  100/80/30/5

Pantone 485 Red - 10/100/100/5

Pantone 123 Yellow - 0/27/100/

INSTRUMENTS

Max, Min, & Weighted Averages

While in the normal-measuring mode, press the “MAX/MIN” button to 
view the maximum, minimum, and weighted average readings. Each press 
of the “MAX/MIN” button will display the MIN, MAX, STEL (short term 
exposure limit), and TWA (time weighted average), in sequence and will 
then return to normal-measuring mode. 

In MIN and MAX modes, the LCD will show the minimum and maximum 
readings of CO2 on the main display and of the readings on the lower 
displays.

In STEL and TWA modes, the main display will show the weighted aver

-

age of CO2 readings for the past 15 minutes (STEL) or 8 hours (TWA). The 
lower displays will continue to measure normally. 

NOTE

: If the meter is turned on for less than 15 minutes, the STEL value 

will be the weighted average of readings taken since power on. This is the 
same for TWA values before 8 hours of activity. 

It takes at least 5 minutes to calculate STEL and TWA. The display will 
show “----” during the first 5 minutes from power on. While all readings 
are held unchanged, STEL and TWA will keep updating every 5 minutes. 

Auto Power Off

This meter turns off automatically after 20 minutes of inactivity. To override 
the function, turn the meter off and hold down the “SET” and “HOLD” 
buttons for 2 seconds to turn on the meter on. “n” will appear on the LCD 
if indicating Auto Power Off is deactivated. NOTE: the auto power off 
function will be disabled during calibration mode. 

Alarm

This meter features an audible alarm when CO2 concentrations exceed 
a set limit. To set-up the alarm, press and hold the “SET” button for two 
seconds. “AL” and P1.0 will appear on the LCD. Press the “ENTER” but

-

ton to modify the alarm setting. 

 

continued...

www.

.com

[email protected]

1.800.561.8187

Summary of Contents for R9900











Reviews: