Reece ISSY GLIDE 750 Installation Instructions Manual Download Page 6

by 

OPEN SKY DESIGN

ISSY

GLIDE VANITY UNIT

DRAWER INsTALLATIoN 
INsTRUCTIoNs

The Nova Pro Drawers can be installed 
or removed with just one movement.

To install drawer

1. Fully extend runners
2. Place drawer on runners
3. Close drawer firmly until a double

click is heard

Ensure drawer is engaged to BOTH 
runners. See

 Refitting Drawers

To remove drawer

4. Fully extend drawer
5. Hold drawer sides as above and

firmly lift off runners

TooL-FREE sIDE ADJUsTmENT

1.  Press the catch hooks     (left and 

right) to the back

2. Lift the front up lightly and slide over

ribs. Adjustment range 

± 1.5mm.

HEIGHT ADJUsTmENT

1. Lightly loosen the screw     and

adjust the front with the eccentric 
screw      into the desired height 
position

2. Tighten screw  

Adjustment range 

± 2mm.

TILT ADJUsTmENT oF FRoNT

Readily accessible tilt adjustment facility 
on the inside of the drawer side. The tilt 
adjustment is achieved by adjusting this 
screw located at the rear of the drawer.

Note:

 Only available on 122mm drawer 

sides

REFITTING DRAWERs

It is important that the drawers 
are refitted correctly if removed for 
installation. If the drawer is not locked 
into the runner system at all four corners 
the drawer will not function correctly. 
Please follow the Install Instructions for 
fitting the drawer then check the drawer 
is correctly locked onto the runner by 
carrying out the following checks.
1. Fully extend the drawer. Use gentle

upward pressure to determine if
each back corner is locked onto the
runner. If a corner has not locked
on, remove the drawer and reinstall
using the Drawer Install Instructions
guide.

2. Fully extend the drawer. Apply

gentle upward pressure to the front
2 corners to test both corners are
locked onto the runners. Finally give
a gentle pull forward on both sides.
If the drawer is correctly locked onto
the runners the drawer should not
be able to pull forward past its full
extension. If any corner is not locked
onto the runner remove the drawer
and reinstall using the Drawer Install
Instructions provided.

DRAWER INsTALLATIoN AND ADJUsTmENT

3

3
4

4

3

2

2

2

page 6 of 6

Summary of Contents for ISSY GLIDE 750









Reviews: