8
I. PRIOR TO FIRST USE
Carefully remove the unit and its accessories from the packaging. Dispose of all packaging
materials and promotional stickers.
Keep all warning labels, warning stickers (if any), and the serial number identification label
located on the housing.
After transportation or storage at low temperature allow the appliance to stay at room temperature
for at least 2 hours before use.
Wipe the housing with a damp cloth, removable parts rinse with warm water. Dry thoroughly before
operating.
Place the appliance on a flat, stable, and horizontal surface away from wallpaper, decorative
coatings, electronic appliances, or any other objects or cabinets that could be damaged by
steam, humidity, or high temperature.
Before operating, make sure that the outer and inner parts of the pressure multicooker have
no dents, cracks or any other visible damages. There should not be any obstructions between
the heating element and the bowl.
ATTENTION! It is forbidden to lift the device with the filled bowl by the handle.
ATTENTION! It is forbidden to lift the device by the handles of the bowl!
Do not switch the device on without the inside of the bowl or empty bowl — in case of accidental
start of the cooking program it will lead to a critical overheating of the device or damage the
non-stick coating. Before frying products, pour a little vegetable or sunflower oil into the bowl.
II. OPERATION
Disabling audible signals
You can turn audio on and off in any mode, apart from when setting the programme up before
starting.
To do this, press and hold the button for a few seconds. The <> light will switch on. To enable
audio, press and hold the button again.
The beep will be supplied, the indicator will turn off.
Control panel lock
The REDMOND RMC-M96 multicooker is equipped with a control panel lock function to prevent
misuse.
You can lock and unlock the control panel in any mode, apart from when setting the programme
up before starting. To do this, press and hold the button for a few seconds. If the control
panel is locked, then will be lit on the display.
Standard Operating Procedure for Automatic Programmes
IMPORTANT! When using the water boiling device (for example, when boiling products), DO
NOT set the cooking temperature above 100°C. It may result in overheating and failure of the
device. For the same reason, DO NOT use the “
ЖАРКА”
, “
ХЛЕБ”, “ВЫПЕЧКА”, “ПИЦЦА”, “ФРИТЮР”
and “
ЧИЗКЕЙК”
programs to boil water.
1. Measure the ingredients according to the recipe.
2.
Put them into the bowl. Make sure that all the ingredients including liquid are below the
scale mark indicating maximum capacity. Place the bowl inside the device. The bowl and
the heating element must fit tightly.
Use only the bowl supplied or compatible with this model when using the multicooker. See
www.redmond.company for compatible bowls. DO NOT use any other utensils!
DO NOT process food directly in the bowl! This may damage the non-stick coating, deform the
bowl and damage the appliance.
3. Close the lid of appliance.
When using some programmes, cooking can be done with the cover off, follow the instructions
in the recipe book.
ATTENTION! If you cook at high temperatures using a large amount of vegetable oil, always
leave the lid of the device open.
4. Connect the power cord to the connector on the device.
5. Plug in the appliance. The appliance will go into the standby mode (the display
shows – – – –).
6. Repeatedly press and buttons to select the cooking program. Switching programs
is carried out in a circle, the selected program indicator
and “Старт” button indicator will
flash.
7.
If necessary, change the default cooking time (see “Setting Cooking Time”). The “МУЛЬ
-
ТИПОВАР” program also provides the ability to adjust the cooking temperature before
starting
(see “МУЛЬТИПОВАР” programme – setting cooking temperature before starting”).
8. If necessary, set the delay start time (see “Time Delay Function”).
When setting cooking parameters, the value being changed will flash on the display. After
5 seconds of inaction, the changed value will be saved automatically.
After 1 minute of inaction while setting up a programme, the device will go into waiting mode.
Pressing the “Разогрев/Отмена” button while setting the cooking programme will switch the
device to automatic programme selection mode. Pressing the button again will switch the device
to waiting mode
At any stage of setting up, pressing and holding the “Старт” button will cause the cooking
programme to begin with the current settings. Unchanged parameters will stay as the default.
9.
Press and hold the “Старт” button to start the cooking program.
While the programme is underway, there will be a timer counting down the time remaining.
The selected program indicator, indicator
, the “Старт” button indicator is lit. If the
auto-heating function is active, the light will be lit (see “Keep Warm Function (automatic
