background image

US-4

HEZ2450S/HEZ3050S

3. Warning labels on the machine

For safe operation and maintenance, symbols are
carved in relief on the machine. According to these
indications, please be careful not to take a mistake.

(a) The port to refuel the "MIX GASOLINE" 

Position:

FUEL TANK CAP

(b) The direction to close the choke

Position:

AIR CLEANER COVER

(c) The direction to open the choke

Position:

AIR CLEANER COVER

4. Symbols on the machine

15m (50ft)

(1)

(2)

(3)

(4)

(5)

(6)

*1: The year will be changed every year of manufacturing.
*2: The initial number will be changed every year of

manufacturing.

*3: SP : Sealed tank made of HDPE or PE.

USE JASO FD OR ISO L-EGD GRADE 50:1 OIL

MANUFACTURED:

       THIS ENGINE MEETS U.S. EPA AND CALI-
     FORNIA EXH / EVP REGS FOR 

2009*

1

 S.O.R.E.

   ENGINE FAMILY : 9HQZS.0244XY*

2

   DISPL.: 24cc

EMISSION CONTROL SYSTEM : EXH;EM/EVP;SP*

3

COMPLIANCE PERIOD :     300 HOURS

REFER TO OPERATOR'S MANUAL FOR MAINTE-
NANCE, SPECIFICATIONS AND ADJUSTMENTS.

EMISSION CONTROL INFORMATION

USE JASO FD OR ISO L-EGD GRADE 50:1 OIL

MANUFACTURED:

       THIS ENGINE MEETS U.S. EPA AND CALI-
     FORNIA EXH / EVP REGS FOR 

2009*

1

 S.O.R.E.

   ENGINE FAMILY : 9HQZS.0294NO*

2

   DISPL.: 29cc

EMISSION CONTROL SYSTEM : EXH;EM/EVP;SP*

3

COMPLIANCE PERIOD :     300 HOURS

REFER TO OPERATOR'S MANUAL FOR MAINTE-
NANCE, SPECIFICATIONS AND ADJUSTMENTS.

EMISSION CONTROL INFORMATION

■ 

EMISSION CONTROL

An emission control label is located on the engine.

(1) Read owner's manual before operating this machine.
(2) Wear head, eye and ear protection.
(3) Warning! Danger of kickback.
(4) Beware of thrown objects.
(5) Warning/Attention
(6) Keep all children, bystanders and helpers 15 meters away from the machine.

If warning label peel off or become soiled and impossible to read, you should contact the dealer from which you
purchased the product to order new labels and affix them in the required location(s).

Never modify your machine.
We won't warrant the machine, if you use the remodeled machine or you don't observe the proper usage
written in the manual.

WARNING

IMPORTANT

[ HEZ2450S ]

[ HEZ3050S ]

Summary of Contents for STICK HEZ2450S




















Reviews:

Related manuals for STICK HEZ2450S