background image

4

In order to ensure proper and safe

operation of your brushcutter

• Read this Owner/Operator Manual

carefully. Be sure you understand how to
operate this unit properly before you use
it. Failure to do so could result in serious
injury.

• Be sure to keep this manual handy so that

you may refer to it later whenever any
questions arise. Also note that you are
requested to contact the dealer from
whom you purchased the product for
assistance in the event that you have any
questions which cannot be answered
herein.

• Always be sure to include this manual

when selling, lending, or otherwise
transferring the ownership of this product.

• This product has been designed for use in

cutting grass, and it should never be used
for any other purpose since doing so could
result in unforeseen accidents and injuries
occurring.

• You should never use this brushcutter

when under the influence of alcohol, when
suffering from exhaustion or lack of sleep,
when suffering from drowsiness as a result
of having taken cold medicine, or at any
other time when a possibility exists that
your judgment might be impaired or that
you might not be able to operate the
brushcutter properly and in a safe manner.
Also be sure never to allow children or
anyone unable to fully understand the
directions given in this manual to use this
brushcutter.

Safety Precautions

• Avoid running the engine indoors. The

exhaust gases contain harmful carbon
monoxide.

• Never use your brushcutter under

circumstances like those described below:

1. When the ground is slippery or when

other conditions exist which might make
it not possible to maintain a steady
posture while using the brushcutter.

2. At night, at times of heavy fog, or at any

other times when your field of vision
might be limited and it would be difficult
to gain a clear view of the area where
the brushcutter is to be used to ensure
safety.

3. During rain storms, during lightning

storms, at times of strong or gale-force
winds, or at any other times when
weather conditions might make it unsafe
to use this product.

• When using this product for the first time,

before beginning actual work, take the
brushcutter to a wide, clear, open space,
turn on the power, and practice handling
the brushcutter until you are sure that you
will be able to handle in it properly in actual
operation.

• Lack of sleep, tiredness, or physical

exhaustion results in lower attention spans,
and this in turn leads to accidents and
injury. When planning your work schedule,
allow plenty of time to perform the work of
cutting and allow plenty of time for rest.
Limit the amount of time over which the
brushcutter is to be used continuously to
somewhere around 30~40 minutes per
session, and take 10~20 minutes of rest
between work sessions. Also try to keep
the total amount of work performed in a
single day under 2 hours or less.

Summary of Contents for BC2300DL













































Reviews: