background image

SRM-510ES

10-52F-01

1

INTRODUCTION

W

e are constantly working on technical im-

provement of our products. For this reason, 
technical data, equipment and design are 
subject to change without notice. All speci-
fications, illustrations and directions in this 
SERVICE DATA are based on the latest 
product information available at the time of 
publication.
ECHO SERVICE MANUAL Ord. 402-25 
(Model : SRM-4000, RM-4000) contains lots 
of information for servicing this model.

1

SERVICE DATA

TRIMMER/BRUSHCUTTER

SRM-510ES

(Serial number : 36000001 and after)

CONTENTS

 

page

1 SERVICE INFORMATION

 .............................. 2

1-1 Speci

fi

 cation ............................................... 2 

1-2 Technical data ............................................. 3
1-3 Torque limits................................................ 4
1-4  Special repairing materials ......................... 4
1-5 Service limits............................................... 5
1-6 Special tools ............................................... 6

2 CARBURETTOR ADJUSTMENT PROCEDURE

 .. 7

2-1  General adjusting rules ............................... 7
2-2  Presetting Idle adjust screw, Idle mixture 
needle and Hi speed mixture needle .................... 7
2-3 Adjusting carburettor................................... 8

Reference No.

 

10-52F-01

R E V I S E D :     2 0 1 0 0 2

ISSUED: 200906

Summary of Contents for SRM-510ES









Reviews: