background image

• 

Make sure that the fuel filler cap is mounted 

tightly and no flammable substances are kept in 

an open vessel.

•  Sparking can occur 

when working with 

the battery and the 

heavy cables of the 

starter circuit. This 

can cause battery 

explosion, fire or eye 

injury. Sparking will 

not occur after the grounding cable (normally 

negative, black) is removed from the battery. 

•  Disconnect the grounding cable from the battery 

first and reconnect it last.

•  Do not make a bridge short circuit across the 

starter relay to run the starter.

•  Be very careful when handling battery acid. 

Acid on skin can cause serious corrosive burns. 

If you spill battery acid on your skin, rinse 

immediately with water. 

•  Acid in the eyes can cause blindness, contact a 

doctor immediately. 

•  Be careful when 

servicing the battery. 

Explosive gases form 

in the battery. Do 

not do maintenance 

on the battery when 

smoking or near 

open flames or 

sparks. The battery can explode and cause 

serious injury or damage.

•  The machine is tested and approved only 

with the equipment originally supplied or 

recommended by the manufacturer. Only use 

approved repair parts for the machine.

•  The mulch blades must only be used in familiar 

areas when higher quality mowing is necessary.

•  Regularly clean the deck and the underside of 

the deck. Avoid spraying engine and electrical 

components with water.

Transport

•  The machine is heavy and can cause serious 

crushing injuries. Be more careful when it is 

loaded on or removed from a vehicle or trailer.

•  Use full width ramps for loading machine into a 

trailer or truck.

•  The two front and rear tie down straps must 

be used and directed down and out from the 

machine.

• 

Check and abide by local traffic regulations 

before transporting the machine on roads.

•  Use an approved trailer to transport the 

machine. Turn off the fuel supply. Fasten the 

machine down with approved devices such as 

bands, chains or straps.

•  Do not tow this machine, it can cause damage 

to the drive system.

•  Do not tow trailers, etc. with this mower. They 

can jackknife or overturn, causing damage to 

the mower and possible serious injury to the 

operator.

•  Load the unit onto truck or trailer by driving up 

ramps of sufficient strength using a slow speed. 

Do not lift! The machine is not intended to be 

lifted by hand.

•  When loading or removing this machine, do not 

use more than the maximum recommended 

operation angle of 10 degrees.

  WARNING!

  Use extreme care when 

loading the machine into a truck or trailer using 

ramps. There is the possibility of serious injury 

or death if the machine falls off the ramps.

IMPORTANT INFORMATION  

The park brake 

is not sufficient to lock the machine in place 

during transport. Make sure the machine is 

correctly fastened to the transport vehicle. 

Always reverse the machine onto the transport 

vehicle to avoid tipping it over.

Towing

If machine is equipped with a tow hitch, use much 

more caution when towing. Do not let children or 

others in or on towed equipment.

Make wide turns to avoid jack-knifing. Travel 

slowly and leave more distance to stop. Do not 

tow on sloped ground. The weight of the towed 

equipment may cause loss of traction and loss of 

control.
Follow the manufacturer’s recommendation for 

weight limits for towed equipment. Do not tow 

near ditches, canals, and other hazards.

Spark Arrestor

This mower is equipped with an internal 

combustion engine and must not be used on 

or near unimproved forested, bush covered 

or grassy lands unless the engine’s system is 

equipped with a spark arrestor meeting applicable 

local or state laws. Federal laws apply on federal 

lands. If a spark arrestor is used, it must be 

maintained in good working order by the operator.

A spark arrestor for the muffler is available 

through your authorized RedMax dealer.

10

SAFETY

Summary of Contents for 96767110200









































Reviews: