background image

                                                                                                           

 

13 | 

P a g e

 

 

 

 

 

 

 

 

 

Ensure that the heater is turned off (the switch on the back of the unit should be in the 

off 

position), Unplug the power cord from the wall outlet before cleaning. 

 

Carefully wipe the exterior of the heater with a soft, damp (not wet) cloth and dry thoroughly 
with a soft, dry cloth. 

 

Over time dust may accumulate on the front vent of the heater. This can be removed by wiping 
with a damp cloth, or carefully cleaning using a vacuum cleaner with brush attachment. 

 

Do not use harsh or abrasive cleaners

 

to clean your heater, as these will damage the surface. 

 

Clean the filter every 30 days or as needed. 

 

WARNING TO USER 

 

Any other service should be performed by a certified electrician specialist or by authorized service 
representative! The manufacturer shall not be liable in the event of non-observance of the above 
instructions!   
 

 

 

 

 

 

 

 

 

         

    Caution!! Disconnect power cord before servicing 

 

 
 
 
 
 

Summary of Contents for CONCEPT R-2





















Reviews: