background image

23

USER MANUAL

▪  

Red Rooster Lifting Limited 

 Nauta House, The Meadows, Oldmeldrum, Aberdeenshire, AB51 0EZ 

 Tel: +44 (0) 1651 872101 

 

M01-AH8 REV0

SERVICE DATA

 

Maintenance chart

TCR-6000/2

NO.

DESCRIPTION

CHECK POINTS

STD DIMENSIONS & MAX FOR REPLACEMENT

91

Wheel 

 

Replace if loadsheave part is badly damaged or worn.

96

Chain Guide

Replace if the wear of any part of the chain guide exceeds more 

than 1mm.

97

Chain Separator

L

 W

STD L   = 25.5mm     MAX L   = 28mm

STD W  = 47mm 

   MAX W  = 49mm

Replace if any of the above dimensions exceed maximum wear.

115

Hook

Dimensions:         STD L  = 65mm   MAX L  = 66.3mm

                             STD H = 49mm   MIN H  = 47mm

Check dimensions as casting size can vary. Replace if beyond 

maximum ‘L’ or ‘H’.

There is some variation in the 'H' size on hooks so it is best to 

measure the hook when new and then allow up to 1mm of wear.

101

Load Chain

5 links L

 d

STD L   = 69.5mm     MAX L   = 70.5mm

Replace if L exceeds MAX L.

STD D   = 11.2mm     MIN D   = 10.35mm

Replace if D exceeds MIN D

Also replace if the link chain is severely damaged.

Measure the chain diameter (d) with point caliper.

d

d

L

 H

Summary of Contents for TCR-6000/2
























































Reviews: