RED ROOSTER TCR-6000/2 Page 22 User Manual Download

Page: 22 / 55

USER MANUAL

▪

Red Rooster Lifting Limited

▪

Nauta House, The Meadows, Oldmeldrum, Aberdeenshire, AB51 0EZ

▪

Tel: +44 (0) 1651 872101

▪

M01-AH8 REV0

SERVICE DATA

Maintenance chart

TCR-6000/2

NO.

DESCRIPTION

CHECK POINTS

STD DIMENSIONS & MAX FOR REPLACEMENT

Vane

STD L = 82mm

MIN L = 81mm

STD W = 27mm

MIN W = 25mm

STD T = 4mm

MIN T = 3.5mm

Replace if any of the width, length and thickness is less than

the stated minimums.

Brake Disc

STD T = 8mm MIN T = 7.3mm

Below minimum for replacement.

Cage

Replace when there is a large or uneven play in the pin hole.

Star Gear

Pinion

Wheel Ring

Gear

Replace if there is a step on the surface of the gear teeth.

step

Replace if there is a step on the surface of the pin.

If the pin is replaced, replace the needle bearing and star gear

at the same time.

step

Summary of Contents for TCR-6000/2
























































Search results

Summary of Contents for TCR-6000/2

Reviews:

Related manuals for TCR-6000/2

Brands by name

Popular brands

RED ROOSTER TCR-6000/2, User Manual

Search results

Summary of Contents for TCR-6000/2

Reviews:

Related manuals for TCR-6000/2

Brands by name

Popular brands