background image

21

USER MANUAL

▪  

Red Rooster Lifting Limited 

 Nauta House, The Meadows, Oldmeldrum, Aberdeenshire, AB51 0EZ 

 Tel: +44 (0) 1651 872101 

 

M01-AH12-LF REV0

SERVICE DATA

 

Maintenance chart

TCS-500

NO.

DESCRIPTION

CHECK POINTS

STD DIMENSIONS & MAX FOR REPLACEMENT

103

Chain Guide

Replace if the wear of any part of the chain guide exceeds more 

than 1mm.

104

Chain Separator

STD L   = 12.8mm     MAX L   = 15mm

Replace if any of the above dimensions exceed maximum wear.

250

260

Hook

Swivel Hook

Dimensions:         STD L  = 35mm      MAX L = 35.7mm

                             STD H = 15mm      MIN H = 14.4mm

Check dimensions as casting size can vary. Replace if beyond 

maximum ‘L’ or ‘H’.

There is some variation in the 'H' size on hooks so it is best to 

measure the hook when new and then allow up to 0.5mm of 

wear.

274

257

Sleeve Pin

Sleeve Pin

 

Measure the contact area of the pin and the chain.

Replace if the wear exceeds 1mm. 

111

Spring Pin

Replace when the following limits are exceeded:

Usage of 10 years, 400 hours operation, 500000 cycles.

If external wear exceeds 1mm, replace.

114

Load Chain

5 links L

 D

STD L   = 95mm 

   MAX L   = 96.9mm

Replace if L exceeds MAX L.

STD D   = 6.3mm 

   MIN D   = 5.9mm

Replace if D exceeds MIN D

Also replace if the link chain is severely damaged.

Measure the chain diameter (d) with point caliper.

D

D

L

W

ear

L

 H

Summary of Contents for TC5-500-LF























































Reviews: