background image

LIMITED WARRANTY

The Company warrants the products it manufactures against defects in materials and workmanship 

for a period limited to two years from the date of shipment, provided the products have been stored, 

handled, installed, and used under proper conditions. The Company’s liability under this limited 

warranty shall extend only to the repair or replacement of a defective product, at The Company’s 

option. The Company disclaims all liability for any affirmation, promise or representation with 

respect to the products.
The customer agrees to hold Red Lion Controls harmless from, defend, and indemnify RLC against 

damages, claims, and expenses arising out of subsequent sales of RLC products or products 

containing components manufactured by RLC and based upon personal injuries, deaths, property 

damage, lost profits, and other matters which Buyer, its employees, or sub-contractors are or may be 

to any extent liable, including without limitation penalties imposed by the Consumer Product Safety 

Act (P.L. 92-573) and liability imposed upon any person pursuant to the Magnuson-Moss Warranty 

Act (P.L. 93-637), as now in effect or as amended hereafter.
No warranties expressed or implied are created with respect to The Company’s products except those 

expressly contained herein. The Customer acknowledges the disclaimers and limitations contained 

herein and relies on no other warranties or affirmations.

Red Lion Controls
Headquarters
20 Willow Springs Circle
York PA 17406
Tel +1 (717) 767-6511
Fax +1 (717) 764-0839

Red Lion Controls

China

Unit 302, XinAn Plaza

Building 13, No.99 Tianzhou Road

ShangHai, P.R. China 200223

Tel +86 21 6113 3688

Fax +86 21 6113 3683

Red Lion Controls

Europe

Softwareweg 9

NL - 3821 BN Amersfoort

Tel +31 (0) 334 723 225

Fax +31 (0) 334 893 793

Red Lion Controls

India

201-B, 2nd Floor, Park Centra
Opp 32 Mile Stone, Sector-30

Gurgaon-122002 Haryana, India

Tel +91 984 487 0503

Summary of Contents for ITMA









Reviews: