manualshive.com logo in svg

Red Jacket Quick-Set VSFC Submersible Turbine Pump, Installation, Service, & Parts Lists, Page: 19 / 70

Share
Download
Red Jacket Quick-Set VSFC Submersible Turbine Pump Installation, Service, & Parts Lists Download Page 19

Installation

Installing the Pump

13

2.

Place the new gasket on the new UMP so that all holes align (see Figure 8).

Gaskets from competitive UMPs will not seal properly and performance will be
reduced.

3.

Align the UMP positioning dowel insert in the proper hole in the discharge head (see Figure 7) and push the 
UMP into position using hand force only. The UMP should be snug against the discharge head prior to 
installing the UMP retaining bolts.

Use hand force to push the UMP onto the discharge head. If the UMP does not seat
snug against the discharge head, remove the UMP and correct the problem. 

4.

Install the UMP retaining bolts and lock washers (see Figure 8). Snug and then torque the bolts using a cross 
pattern technique. Torque to 7 ft-lbs (11 N•m).

Do not use the bolts to pull the UMP into position. Use the cross pattern technique.
Do not over torque the bolts. Not following instructions may cause parts to fail.

Figure 8.   Aligning The UMP Gasket

Installing the Pump

Disconnect, lock out, and tag power at the panel before starting to 
service the pump

When servicing equipment, use non-sparking tools and use caution when removing or installing 
equipment to avoid generating a spark.

NOTES: 

• The Red Jacket STP is designed to operate in a Class 1, Group D atmosphere.

• The manufacturer may recommend new specifications and installation instructions.

• The product temperature must not exceed 105°F (41°C) because the thermal overload protectors in the 

submersible motor may trip.

CAUTION

WARNING

WARNING

rjpumps/fig6.eps

UMP

Positioning

dowel

Gasket

Discharge head

WARNING

OFF

Summary of Contents for Quick-Set VSFC Submersible Turbine Pump







































































Reviews:

No comments